hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,
This seems to be an issue that pops up often. However, I wasn't able to find an answer here in the Nordic forum.
What I have:
a number of vendor services ...
I'm trying to change the SD version number of a test-S132-file, soI can "see" that the DFU was successful in my app. I can already read the current version (from 0x300C in...
Does anyone had controlled LoRa module with nRF5x??
I have nRF51822(BLE400(PCA10001)), nRF52832(PCA10040) and Semtch SX1276RF1JAS.
I hope to control LoRa module using nRF...
Hello All,
I am looking for a stand alone small transmitter/receiver that can be powered from a watch battery with a range of at least 300m. Is any of the nordic solutions...
hi,
i am working on code which require to store data array of 20x20 to store in flash area using FDS or any other possibilities.
1)i confused with FDS concept. how i can...
Hi,
we are now in the second round of prototyping - we'd like to move away from the chip-antenna based design to a PCB antenna. We have come up with two different ideas...
Here
My device (chip nrf51822_xxAA) exist softdevice 8.0.3 and BLE uart application work fine which flash by the ST-link in Keil MDK(5.20).
Now I try to add bootloader to...
Hello
I've found your example in the dev-zone and migrate the project to SDK10 and will probably do the same for SDK11.
However, I've got a problem in my project. When...
hi,
i want to implement rtxos in my nrf52832 application. one of the nrf52832's feature is ARM Cortex -M4 32-bit processor with FPU, 64 MHz.
my question is, why the...
Dear Nordic.
I am developing bootloader without SD (s120_nrf51822_1.0.1).
And after execution of bootloader, jump to application working with SD.
Flash composed like...
I tried to compile blinky sample in SDK12 with make tool-chain. I got 3 errors:
Makefile:214: Cannot find include folder: ../../../config/blinky_pca10040_s132
Makefile...
I converted a project from uVIsion to IAR, and I get an error when I use app_timer_start(); the error says: Error[Pe167]: argument of type "void ( )(void)" is incompatible...
I don't need to connect the master with the peripherals, but i have to know how is the maximun quantity of scan response that can accept the master.
In the example ble_app_multilink_central...
In trying to move to SDK 12.0.0 from 10.0.0 I get the error:
"...components/includes/app_error.h:33:23: fatal error: ant_error.h: No such file or directory
#include "ant_error...
Hi,
I want to run BLE mesh network example on my Dev board to understand it better.
I am running it on SDK v8.1 and using ble_app_proximity example S130.
Following...
