I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
Hi,
1. Does nRF52840 CKAA WLCSP support QSPI 32MHz?
2. What should qSPI 32MHz measured CLK waveform look like?
3. Is there a 32M QSPI CLK sample diagram actually measured...
I finally had success in getting a SPIM master running with a single SPI slave (Honeywell sensor running CS 4 on the Arduino R3 header) on my nRF9160DK. But now I need to...
Dear all:
I am developing a ble scanner using RADIO Peripheral.
I have 2 questions to ask
1.When is the END event triggered?, How does the hareware know the packet is...
I received the hardfault in the following image.
The function at the address 0x00028C44 is:
The hardfault did not occur again after resetting. I'm not sure why this...
Hello,
We have a PIC32 controlling the NRF24L01 with some sucess so far.
But sometimes we get the chip in a state that we can't get off.
We still cannot pinpoint the...
Hi Team,
I am developing an application that nordic chips receive data from msp430 chips by the SPI, and send them out.
Nordic can receive the data from the msp430, but...
Hello everyone,
I tried to add the long press event into my bsp_event_handler without success. I get the normal button press event, but the long button press event is not...
Dear Nordic FAE:
Where can I find the nrf52840-CIAA REACH report?
i can not find it by
focenter.nordicsemi.com/index.jsp?topic=%252Fcom.nordic.infocenter.sdk5.v12.2...
Issue:
While trying to initialize and check the viability of an I2C interface using TWIM, my NRF_TWIM_TASK_STOP never triggers NRF_TWIM_EVENT_STOPPED.
Code:
This causes...
Hi,
I have installed the v1.8.0 nrf connect sdk and created a new application using the nrf connect vscode extension based on the ble/throughput example. Created a build...
Dear Nordic Engineer
I would like to know the version of openthread in NCS 1.8.0? And what is the otbr posix version corresponding to rcp firmware? It is reflected in the...
Hello,
I am using NRF connect SDK v1.5.1. I want to delete the last paired and all paired from central and peripheral also.
I found that pm_peer_delete() & pm_peers_delete...
Hi,
SoftDevice S112 is not Central support just Peripheral.
The max connection of Peripherals is 4, I didn't understand the meaning ! Peripheral can connect only to Central...
Hi, I am trying to use the nRF52833 development board for Bluetooth direction finding. I am having some problems, and I would appreciate it if I could get your help.
My...
