void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Hello
when hardfault is happaning, I can catch and understand the reset reason easilly, by looking at the map file
however, from time to time, I get a reset without...
I'm using Segger Embedded Studio version 1.6.0 to try to do some testing with SPI for a future project. Currently I am adding SPI functionality to the "Blinky" example: I...
#define SCAN_INTERVAL 0x00A0 /**< Determines scan interval in units of 0.625 millisecond. */
I am a beginner in this field. I am not sure what does this hexadecimal number...
Hi team:
After my device runs normally for more than 10 hours, the issue that THE socket cannot be created occasionally occurs. Once the issue occurs, the socket cannot...
Hi. I'm working on several projects, some of which are not using Nordic chips. I installed the latest Segger J-Link drivers to support a different project. I believe this...
Hi,
I am using nrf_drv_clock_hfclk_release (); in order to release the hfclk, before the call, the internal counter is 1 and the module is initialized.
because the counter...
I'm working on the NRF Connect SDK v1.6.1 and building the zephyr\samples\net\gsm_modem project, since I'm trying to set up and operate a Nimbelink modem. The code references...
Hi everyone,
I would like to change the output voltage and current driver strength of some GPIO ports on the nRF52840. I am using the zephyr driver "gpio.h" API, but the...
When I try to connect to a previously bonded device, I'm getting
Disconnected (reason 0x3d)
and bt_att: Unhandled ATT code 0x1d
and if I delete the bonds again and try...
I am writing a coordinator application based on the zigbee CLI example. I am using SDK for Thread and Zigbee v4.1.
I am using a function in zboss_api called zb_secur_ic_get_list...
Hello,
I'm using SDK nrf5_17.0.2 on nrf52840
I'm implementing a custom nrf block device for a spi nand flash, and I'm getting trouble with the calling site of the nrf_blk_dev_read_req...
Hello Everyone,
I am using NRF52840 development kit, I have compiled the code using SDK15.0.0. I am using soft device as well. I have to implement flash protection in my...
Hi,
I’m finishing the design of a nRF5340-based custom board featuring a NFC coil-inductor antenna. Will orientation of track turns - clockwise or counterclockwise - affect...
