here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi, I am trying to get the voltage level of the battery using the AT_command AT%XVBAT which I tested using the at_client sample. I tried integrating it with my current code...
From looking at the code when a message is posted to "all-nodes" fixed group address of 0xFFFF it does not route. I was unable to find this behavior specified anywhere in...
Hi forum,
I am working on nrf52832, using sdk 15.0.0. I want to send the data(command) from esp32 to nRF52832 through Rx ,Tx . I have done connections rx,tx,gnd . I can...
Hi,
We are developing our stack with soft device using nRF52840 as the Controller and have the below queries
1. How to configure a static random BDADDR which will remain...
The error is
CMake Error at ../../../cmake/extensions.cmake:416 (add_library):
No SOURCES given to target: drivers__spi
This similar to
https://devzone.nordicsemi...
Hello everyone,
Hello everyone, I am a beginner in programming with OS based systems. I would like to get more into development with the Zephyr based NCS. For now, I want...
Hello!
I try to run FatFS example (SD card example, pca10040) from nRF5 SDK on my nrf52832 (ebyte e73) with microSD card with no success. No matter what I'm still getting...
Hi,
I am trying to get the time and UNIX time after LTE connected. but getting 0 only.
please log
date_time_update() function does not support in SDK 1.4.2 so I...
Hi,
In "nRF52832 Product Specification v1.4, it recommends 32MHz with 40ppm as below:
as the question mentioned above, can I use one with 10ppm?
thanks
best regards...
Hi,
I am getting assertion failed error when putting the device in System off. Could you please help me understand why?
Below in the code where the error happens:
...
I'm working on modifying the ble_app_uart pca10040_s132 to send strings stored in flash memory over BLE to the nRF connect app on an iphone. From what I understand the uart_event_handle...
Hi There,
I m trying to use the xxxx\SDK's\nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8\examples\peripheral\spi with the nRF52480 Dongle and I already had applied the...
Greetings
I have an NRF51422 QFAAEO running S210 Soft Device version 3.0.
I have written a Bootloader application that uses Ant-FS as the upload mechanism. During testing...
Hello everyone,
is it normal behaviour to lose data on UART reception when BLE scanning and advertising both are active?
So far I didn't lose serial data if I just run...
hi all.
I am trying to change number of data packets in one time interval.
I don't know the senario to change it.
For first step I wrote this code to change the quee...
