Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
Do I need to carry out ANSI C63.27 regulatory test for coexistence of wireless communication that share the 2.45GHz band if we designed a custom PCB BLE antenna for NRF52840...
Hi,
I have the nRFgo Starter Kit with the radio module (nRF2427LE1) attached. First, does the radio module not have a bootloader already downloaded to it? Next, when I...
Dear Support Team.
We want to support secure DFU on mobile and desktop platforms. Do you have any documentation to implement this on Mac OSX and Windows?
Its an open...
Hi, is there any LE audio sample for NRF5340?
I know the upper layer protocol is under developing on Bluetooth SIG, but is there any possible way to direct use the HCI command...
Hi
I'm developing with nRF52832.
I am using Segger Enbed Studio as a development tool.
When you download a program from Segger, Segger does reset once, and I wonder...
Hi,
I want to run QSPI application example on my nRF52840DK (PCA10056) board with logs seen via UART. I successfully uploaded QSPI bootloader example and Blinky SysTick...
Hello,
I'm developing an BLE application with NCS where I want to be able to change the BLE device name during runtime. Therefore I enabled CONFIG_BT_DEVICE_NAME_DYNAMIC...
Now we development a switch and use it control the light. When i push switch close the light, there was still a faint light. Then i found when NVIC_SetPendingIRQ(EVENT_IRQn...
What I intended was to write x'700' to x'10001080' i.e. NRF_UICR->CUSTOMER[0] !
When ran my application, which outputs NRF_UICR->CUSTOMER[0] to the log, I was very confused...
In firmware I can read the programmed UICR serial number as follows: -
uint32_t serial;
memcpy(&serial, (uint32_t*)0x10001080, 4);
Is it possible to program the UICR...
The peripheral_lbs sample on the nRF5340 with the nRFConnect v1.5.0 builds fine and the merged.hex file downloads fine, but it does not appear to be running, no blinking light...
I have a program that recieves data from another chip over Serial. It sends 2048 blocks of data which than get transmitted to our C2 over mqtt. Problem is that afther 12/14...
Hi,
I am trying to receive and send data from an android device to an nrf52840 device with USB CDC. I have already installed the application using this link https://jimmywongiot...
Hi!
If I build my project with TF-M I noticed that at least the flash usage report differs dramatically compared to the original firmware:
Original:
Memory region |...
