We are having a slight issue when we are trying to update the DFU. The original version had this setting for the data reserve:
#ifndef DFU_APP_DATA_RESERVED
#define DFU_APP_DATA_RESERVED...
Hello!
I am working with the example mpu interface projects located at the following repo:
github.com/.../nrf5-mpu-examples
After converting the Keil projects to...
I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
Hi,
We are using nRF52811 for one of our upcoming product. We plan to upgrade our firmware via DFU. I cant find any support or example codes for this controller for DFU...
Hello Nordic Team,
Currently I'm working in a BLE HID Project (joystick with 16 buttons and 2 axis (x and y)) usign a NfR52832 and modifying the hid mouse example from SDK...
Hi,
As well know, the nrf52832 had build-in a battery level detect function. It can get battery-level by following program
Would you please tell me how to design it...
Hi
When I finished the program and read back, I saw that there was unintentional data at 0x2D000 and 0x2E000.
I used up to 0x26000 addresses. Where is this memory used...
I've taken the basic examples/peripheral/blinky code and tried to add the logging module to it. For some reason the only time I can get the application to run and log correctly...
I am developing a firmware application that needs simultaneous central and peripheral role. I am using sdk 15.2.0 and was experimenting on dev board PCA10040. I have taken...
Hello,
I want that nRF9160 goes into PSM on boot until a button is pressed, do someone have a good link about PSM please ?
How can I do a software reset with a clean lte...
Dear people,
I use a pca10056 (alternatively the pca10059 dongle) and have compiled the connectivity firmware as described on the github page (release 4.1.1).
The only...
I use nrf5_SDK_for_Mesh_v3.2.0_src\examples\serial and board pca10040.
Supported commands.
In [2]: for i in range(0, 10): send(cmd.Echo("Hello: " + str(i))); time.sleep...
Hi, I'm reading the nRF5340 OPS v0.5.1 document and in section 3.2 ("Memory") there is a reference to "256kB of peripheral RAM". However, the document doesn't explain what...
Hi there,
I'm working on nrf82382, try to use COMP function to monitor the voltage of AIN0(p0.02), but seems not working, no example for the COMP. and then I found the...
We enable TX notification of NUS service with bonded iOS (iPhone), iPhone constantly sends TX_READY command until disconnect.
Can you confirm this is correct behavior. ...
Hi, I am working with the adxl362 sensor and the nrf9160 SPI example ( https://github.com/Rallare/fw-nrfconnect-nrf/blob/nrf9160_samples/samples/nrf9160/spi/src/main.c ) and...
Hi, I am working with the adxl362 sensor on the Thingy91 and I want to set the trigger of the sensor to a specific value.
In the datasheet ( https://www.analog.com/media...
