here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi guys,
I'm working on a project that recently got a change request to enable BLE. I've designed a custom board with the NRF52832 that should meet the requirements.
In...
Hello,
i just wanted to compile a example project out of the box: ble_app_uart.
S132. SES. PCA10040
Surprice, did not work, why do you provide not working examples...
Trying to use a standard delay function to keep and output low for several seconds. It is P0.10 on the 52840 set to Active Low and I do see it transition to a low on the o...
Dear,
I am using both nRF52840 UART (UART0 and UARTE1) on the nRF52840 DK.
The default pin assignement is used, such as
UART0 pins are TX/RX 0.6 & 0.5 and
UARTE1...
Hi NRF team,
I am working on one project. I have used 2 PDM Microphones (MMICT5838-00-012). And I have used Zephyr RTOS for development.
I have used the LC3 encoding and...
Hi,
I'm working on a project using MCUboot, TFM, and a network core app. We use MCUboot with an external flash module for OTA firmware updates.
Recently, we tried upgrading...
Hi,
I am following DevAcademy Lesson 5, HTTP over Wi-Fi (Exercise 2), which involves adding TLS to an HTTP connection.
When I remove CONFIG_WPA_SUPP_CRYPTO_PSA=y , I am...
Using an nRF54L15 here (if that matters) and adding mcuboot via sys build to my project. Couple questions:
- How would one adjust the logger baud rate to something other...
Hello,
I have the nRF5340 DK and I want to program/debug an external SoC. I see that in order to do that I can use the connector P19 to connect to an external board with...
I am using an nrf5340 DK instead of the audio DK. Is BT LE possible with this DK. Is there any difference beween NRF5340 DK and audio DK in terms of microntroller.
Hello,
I’m using VS Code with the nRF Connect extension. When I try to build the “bme68x_iaq” application to upload it later to the Nordic Thingy:53 and read its data, I...
Hi,
I have verified the firmware upgrade and file transfer functionality from a Linux-based device to the customized nrf52840 board using the mcumgr tool.
However, the...
Hello, everyone!
I'm interested to know about the possibility of mixing BLE audio and custom BLE Characteristic in one single nRF5340 application.
For example, we would...
Hi DevZone Community,
My Envriornment
1.9.1 NCS nRF9160DK Current Modem Version : 1.3.2 This question is involving a device which is in production. The issue is, if the...
Hi folks,
Recently picked up a new MacBook (M series) and was excited to try some sample projects on my nrf52840dk.
Unfortunately upon trying to Debug, I get the following...
