here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hello Nordic team,
I followed the official guide to add a custom sensor cluster to my Matter application. Everything built and flashed successfully, and the application...
hello, i have a weired issue with my sensor communication using spi. the code that used the old SDK works, but the one using the new SDK for some reason doesnt. i need to...
Hi,
iam completely new for NRF soc.i want to develope a application where i want to configure the dev name,tx power while run time via mobile application. please tell me...
Currently, we've started developing a new project using the nRF52832 as our controller. Our requirement is quite simple: we need to list out nearby advertising BLE devices...
Hi.
I am using a custom board on an nRF52810 microcontroller and a LIS2DH12 accelerometer connected to it via SPI. SDK version 2.7.0.
Here's my settings:
.dts file ...
I am getting this error on the 7th time I perform an action:
I understand it's an lvgl error and could be specific to lvgl but I think, considering it's only happening...
Hi,
first of all i know that this is not a "good question", but my hacker side is trying to... tweak hex file of softdevice 113 to fit my low memory footprint.
I mean...
Hello everyone, I am working on a custom board based on the nRF5340 and need to implement code execution from an external QSPI memory. The board uses the IS25LP128 memory...
Hi, I am working on a project that collects data from various sensors and transmits it to a Mobile application via BLE. Can I use Isochronous Streaming for it? Can I set up...
Hi community! I have custom boards using nRF5340. A couple boards has suddenly gone bad and unable to be flashed or communicated with after a few reflash cycles.
I've read...
Hello
I would like to sign an image temporarily with west CMake options as described in Enabling a bootloader chain using sysbuild using the comand line:
In it's final...
Dear DevZone:
I use NCS 2.8.0 to build Light Switch FW, my build command as below:
west build -p always --build-dir nrf/samples/matter/light_switch/build -b nrf5340dk_nrf5340_cpuapp...
Dear Devzone,
I currently use the nrfutil dfu serial command to upgrade the firmware, which is OK. I want to upgrade the firmware of 52832 through MCU, so I need to know...
Hello support,
We are developing a battery-operated sensor. For that, we are using nrf5340. Also, we made an enclosure for the sensor.
While developing we found that the...
