here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Is there any problem if I stall older version of nrfjprog in my apple Macbook? Will there be any conflict with the new version already installed. The new nrfjprog have the...
Hi,
I'm trying to send and receive scan request/scan response. The system consists of 2 nrf52840, 1 central and 1 peripheral. They both advertise and scan on 1M and coded...
I'm currently working on a program that automates the Legacy DFU procedure and I'm running into some strange issues with writing to the DFU characteristics.
On the nRF Connect...
Hello,
I am trying to use the FDS module with the Softdevices and Peer manager.
I can store some data and I am able to read the header of the record, but when I try to...
Hi,
I want to use the static version of pc-ble-driver in my c++ code. I am learning cmake but I have no expereince with Ninja. I'm using only the version 6 of the API. My...
Target application 1: Data acquisition is carried out for a 0-1khz high-low level signal. The low level is effective. The count is increased by 1 for each trigger. 2: Use...
Excuse me:
I'm developing a keyboard with nrf52832，Calling ble_hids_inp_rep_send() returns BLE_ERROR_GATTS_SYS_ATTR_MISSING when the keyboard is just connected to ipad4...
Hello All,
I am developing a prototype for one of my application.
I am trying to integrate the zigbee stack to my base firmware.
For my application I am using RTC2....
Hi,
I'm using the example "ble_central/ble_app_uart_c" of nRF5_SDK_17.0.2. Connection to peripheral workes fine.
If the central re-starts while a connection is established...
Hello, there
We made a custom tracker device with nRF9160. During prolonged use, we observed that k_delayed_work_submit_to_queue sometime return -22 and cannot be recovered...
When i change the config NRF_DFU_BLE_BUTTONLESS_SUPPORTS_BONDS to 1
the following error comes, how do I overcome this?
<debug> app: nrf_dfu_svci_vector_table_set() ->...
Hello All,
I am facing binding error if I use UART1 for binding but UART0 is working fine. Refer the below error.
Please let me know the solution to solve this error....
Hey!
I'm trying to adapt a modified version of the open bootloader example for the nRF52820 MCU and have one issue as well as some questions.
I have adapted the build...
Hi,
I am developing a system consisting of a BLE peripheral and central with a custom service (SDK 17, S140, PCA10056).
For the peripheral, I am using a modified version...
I have noted that the code size of my project is reduced by more than a factor of two if I set NRF_LOG_ENABLED to 0. It is also reduced significantly if I set the Log Level...
