Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
Hello,
We were just wondering if it is possible to give user-defined function at the PPI TEP instead of starting timer or generating some GPIOTE task.
Is it possible to...
Hi,
We have a third party active power analyzer which cannot be kept in only current measuring mode. It always provide supply of 3.3 to 5V.
The DK configurations we...
Hi All,
I have up to 8 nRF52832 devices sending data back to a base unit (another nRF52832 device.) What I'm trying to do is have the remote units wakeup at a given time...
I have some questions about FSM，when I enter fsm_init() to perform fsm_any_state_find(fsm_t * p_fsm) completely in mesh_lpn_init() during debug mode by "step into"，the small...
Can you please help i use ble _ nus and after few message i need to change uart baudrate. I cloes uart then init uart with new baudrate parameter but everytime MCU goes to...
Hello Nordic team
I am working on nRF52832 dev board. SDK v-15.2.
My questions are following:
1) How much current consume if we use GPIOTE to register one pin interrupt...
Hello everyone! My team and I would like to port the SDK examples to the Arduino IDE, but we have found that the Arduino IDE does not know what board is being used. We think...
I want to use several GPIOs for different purposes.
for example, - motion detection interrupt by accelerometer - low battery alert interrupt by battery gauge.
However...
I am new to the NRF52840-DK. To burn the program into the kit, I have lots of tries to install nrfGo studio but it gives me the "no board detected readback protection" error...
Hi,
I am using my nRF52832 DK as a sniffer.
I am sniffing a BLE communication between a BLE door lock with a cellphone App.
I can see the device advertises continuously...
Hi,
I am using nRF5_SDK_15.3.0 with ble_app_uart example.When I flashed the ble_app_uart example into my nRF52840 DK it starts to advertising. If there is no connection...
Is it advisable to use coin cell battery power for nodes besides end-devices in a Thread mesh network? Where can I find technical comparison between OpenThread and BLE?
Is it allowed to use nonsymmetric capacitors to get more accurate 32k ? With 2x10pF we run some 35ppm too fast and 2x12pF the clock is 10ppm slow. We could use non standard...
Hi,
I am using SES for programming with an example of BLE Uart NUS and SAADC combined.
I can send raw data, and that all works fine, but conversion to the real ADC voltage...
