I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
When nrfutil is installed with python 3, I get an error when generating bootloader settings page. This does not occur with python 2. As python 2 support expires very soon...
Hi.
I am testing MESH by nrf5SDKforMeshv201src and nRF5_SDK_15.0.0_a53641a.
I have a problem.
My project have one of the client and one of the server.
Client transmit...
Hi I had a question to setup the MCP2515 driver in the zephyr project.
We have a custom board for the decawave DWM1001 module, which uses a nRF52832 chip. They have a device...
Hello I am using a I2C sensor module and I need to tranmit only address to receive data back, but I dont know how.
Program crashes on line 4.
Thank you for your help...
I have a DK52 with another device at attached to the SPI bus. I also have a PPK. Should
I connect the second device to VDD_nrf to count as a load? right now it is connected...
When the bluetooth service function is initialized, sd_ble_uuid_vs_add() is called in the ble_dfu_buttonless_init() function in case of an out of memory error. In the ble_nus_init...
Hello, Is there any evaluation kit available for NRF905? I found this one online but DIGIKEY website says its obsolete::
media.digikey.com/.../nRF905-EVKIT_PS_Rev1.0_Jan2004...
Dear Nordic staff and users,
Now I'm trying to confirm that my local LTE operator supports energy saving modes. It went with flying colours with PSM:
at+cereg=5 OK at...
using SEGGER Embedded Studio for ARM V4.30a, I get a problem of Linking with an nRF5_SDK "blinky" examples. See hereunder the error message:
Seem to be a problem of configuration...
Hello,
I can create a zip file with nrfutil pkg generate and there is a bin file in it? I want to make DFU as a bin file only.
I only want to download the firmware as...
Hello,
I have a question about using pins as output. I'm trying to set 2 pins to "1", but cant fully understand how to use pins on port1.
for example: P0.10 (wich works...
Hallo,
I want to use the UARTE instead of the UART to transmit some audio data to DK. The Basic Project is the i2s example in nRF5_SDK_15.3.0_59ac345.
I implemented the...
I'm starting initial development on a new project using the nRF52832. I've been able to transmit successfully using nrf_serial_write but nrf_serial_read always returns NRF_ERROR_INVALID_STATE...
