I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi!
I try to write SD to 52810 and nrg go studio can't do it. After recover it can't to switch normal window with possibility erase device and SD write. What possible reason...
SDK 14.2 / SD132 5.0 / NRF52832 --> NRF52832
There is a thread here which discusses "when NUS is ready" : https://devzone.nordicsemi.com/f/nordic-q-a/28208/when-is-nus-ready...
I'm using SDK nRF5_SDK_15.0.0_a53641a, and I was able to trigger the hard fault handler from within the Nordic NFC library. Nothing was running. The microcontroller was asleep...
Hi
Some time ago, we purchased a couple of boards, then (I believe) called nRF52 PDK. They are marked PCA10056.
We need to obtain more nodes. From gleaning information...
Hello there,
I'm looking for a good source that explains the ideology of the Nordic methods for programming and debbuging the nrf5 chips so I'm looking for something that...
Hi,
I'am trying to run the example in Software Development Kit > nRF5 SDK > nRF5 SDK v14.2.0 > Examples > Bluetooth low energy examples > Experimental: IoT Examples > TCP...
Hi,
We have our nrf52840 module going to be ready soon. For production testing, what is the recommended and capable lower tester and upper tester? I am sure that nrf51822...
Hi all I am wrking in an sample be program where ble is advertising everey 5 seconds. I have configured app timer with fire period = 5 seconds in order to read a sensor. After...
Hi,
Ipv6 UUID 0x1820 shall be present in the advertising process. Is it mandatory to put it in the ADV_IND message or can it be in the SCAN_RSP one ? ... the scanner, 6BR...
Currently, we are testing Bonding & Connect.
Please see the attached log below.
If Click 「Bond」 on Android App (nRF Connect), disconnection occurs after "PM_EVT_CONN_SEC_SUCCEEDED...
Hello,
I have the following question: when developing a software product, I developed my own service. It consists of one characteristic and several descriptors (valid range...
On our products, we assign a custom sequential mac address to each unit (we use this number in other places in our system). I believe this is an issue due to the bootloader...
Hello all,
We are using nRf52832 DK.
We are trying to run TCP Client example from IOT.we have even burned the s1xx_iot soft device.We are getting the the error "CMSIS...
Hi,everyone!
I need to configure an external interrupt so that when the interrupt is triggered, I can do something else
When I configure it in the following code...
Hi
Hi i am trying my application for sleep and wakeup without gpio. Actually my work is to put my device(battery powered) in sleep for 5 minutes and after that it should...
