Hi there,
I was following the tutorial here https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-6-analog-to-digital-converter-adc/topic/exercise...
Hi,
I need information about adding an additional flash IC to my project. However, I am wondering if there are any limitations regarding the maximum storage capacity that...
Hello, I am trying to read the TI ADC1173 at 10-15 MSPS. It has a 8bit parallel interface. I just need to read a very short amount of time, like 5-10 µs (so up to 150 Byte...
Dear Nordic teams,
we need to develop a wireless audio product with .
Is it possible to develop our 2.4G wireless private protocol by operating registers on the nRF5430...
Hi,
I am developing an application for an nRF52840 using nRF Connect SDK v2.9.0. The application currently uses the Zephyr driver for simple PWM functions on several GPIOs...
Hi everybody. I'm using nRF Connect SDK 2.8.0. I've implemented Zephyr RTOS' core dump functionality on my project. I forced the SoC to write the core dump data on its flash...
Hi, I am fighting with a bug I found in SDK v2.8.0 for BLE scan filter on a test project as follows: 2 Devices (Ezurio BL653-DVK using the nRF52833), both having central and...
Hello,
I'd like to evaluate the Rust HAL for the nrf52 family of devices. But before that I was asked to inquire about the stage of development of the HAL and the support...
I am experiencing an issue with the nRF52840 dongle and programming UART pins. First off, I have developed my application on the nRF52 DK and it works fine and now I am programming...
Hi , I need use the DFU ble without have to generate a packet with the nRFutil. I wan't put a open bootloader on the board, don't need to be secure just easy and fast. But...
I am trying to find the hardware datasheet for the speaker on the Nordic Thingy 52 - can someone help point me towards it?
My end goal is to learn about the characteristics...
Hello!
I have been trying to implement the serialization for STM32L476. During my development I discovered that the deserialization of the SD_BLE_GAP_ADV_SET_CONFIGURE response...
We have a custom board with nrf51822 chipset, and we need to implement the firmware update process, which can support both over-the-air and uart type firmware update.
1...
Hi, we are contemplating moving an existing application to a nordic chip, the nRF52832.
https://infocenter.nordicsemi.com/pdf/nRF52832_PS_v1.4.pdf
Our previous CPU uses...
I'm in the process of implementing a custom layer above ESB in order to allow more than 8 devices to communicate with a receiver (By tagging packets with a device ID)
I...
I used nRF52 SDK V15 and tried to load the sample BLE HID apps into the nRF52-DK Development Board.
I tested both ble_app_hids_keyboard and ble_app_hids_mouse. Both apps...
We have exiting BLE 4.0 device, which should be updated to the mesh. nRF52832
In the DFU for BLE4.0 you could update the booltoader and the softdevice with one update, with...
Hi All,
I am working on fatfs example from sdk 12.2.0 on pca10040, nrf52 dk, nrf52832. And i did not change anything in the code but it seems that my sd card is not getting...
I started with the template app and added BLE services, and I'm continuing by adding a TWI sensor (I2C). I know there is a TWI_sensor example, but I already had some working...
Dear All,
I am working with nRF52840 product. According to my scenario i have 1central unit(master) and up to 19 peripheral unit(slave).
I downloaded SDK 15.3.0 ble_central...
