Dear Nordic Team,
I hope this message finds you well.
Some time ago, we asked about the migration from nRF9160 to nRF9161.
We want to ask the same question regarding...
I want to use the external flash on the nRF5340 DK using SPI as the board I'm developing for will not have QSPI. I used the littlefs sample which has a lot of the settings...
I have made my own NRF52832 Dev board as in the next image:
I received the board, and ICs and hand-soldered them in my home.
however, I am still a newbie in nRF SDK...
For the GetAssistanceData endpoint (POST /location/agnss), if we are using the x-custom-device-id header instead of a device token and registered devices, how can we view...
Hi there,
I was following the tutorial here https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-6-analog-to-digital-converter-adc/topic/exercise...
Hi,
I need information about adding an additional flash IC to my project. However, I am wondering if there are any limitations regarding the maximum storage capacity that...
Hello, I am trying to read the TI ADC1173 at 10-15 MSPS. It has a 8bit parallel interface. I just need to read a very short amount of time, like 5-10 µs (so up to 150 Byte...
I did the program using examples of glucose. But I do not want to enter passkey from central. Because there is no LCD or UART in my device. Which part of the glucose example...
I am developing firmware for my Peripheral Device (nRF52840) using S140 (v7) and SDK 15.3. In my application, I will advertise (with advert payload changes) and support Smartphone...
Hi,
How much is the expected time period from the time VDD goes above 1.75V to main()? I am using a custom bootloader and am seeing a ~4.5s (yes seconds!) delay in getting...
i'm trying to configure the nrf to rx and according to the state diagram i realized that: as the nrf is supplied and the voltage goes over 1,9V the nrf goes in the power down...
Hi, i'm using the nrf24l01 with a zynq board to use it as radiocontrol; i'm trying to configure the nrf as receiver so that i'm able to send data from another nrf connected...
Hi, i'm using the nrf24l01 with a zynq board to use it as radiocontrol; i'm trying to configure the nrf as receiver so that i'm able to send data from another nrf connected...
I am trying to use the LPCOMP API, but I am having trouble with the following function:
nrfx_err_t nrfx_lpcomp_init
(
nrfx_lpcomp_config_t const *
p_config ...
I'm attempting to setup GPIOTE for an output that is set and cleared by different events. The GPIOTE driver doesn't let me initialize an output twice. Is there a way to do...
I have 2 objectives BT beacon and concurrent ESB with Thread using time slotting A. I would like my thread devices to broadcast BT beacons. As this does not require any reception...
Hello. We have product based on NRF51822 chip. 24 bit 4 channel ADC connected through SPI to MCU. Data rate is 250 Hz (4 ms). We send two ADC samples evry notification packet...
I started setting up Zephyr SDK development on my W10 laptop, according to the nRF Connect for Desktop guide, but running into this error when executing pip requirements installation...
Hello,
I'm writing a BLE app that acts as a peripheral and a broadcaster. If a connection is established, I'd like to continue advertising but update the advertising parameters...
Hi,
I am migrating sdk 15.2 to 15.3. Everything works fine, except the nrf logging. Currently, I am using RTT configuration, with default backend enabled. The code is simple...
Hi,
I have been using the PCA10040 and PCA10056 development boards to do some evaluation/testing of the Nordic BTLE radio functionality. We now have purchased standalone...
Hello,
Ive been trying to get simultaneous GPS reception and LTE connectivity for a while now. I've read that this wasn't possibe in the past but it looks like it should...
