Hello everyone,
We are developing products with nrf52840 and our default supply voltage is 1.8V.
Is it possible to program a custom 1.8V board with nRF52840DK?
We are...
Hi
I am using nRF52840 with SDK 15.3.
I have a project where I uses FatFS to write to a SD-card with SPI interface (SPIM3). This works very well.
I am now trying to...
Hi everyone,
I'm currently following the "WiFi Fundamentals" course provided by Nordic, and I'm encountering issues with this specific exercise (l5_e2):
To ensure I wasn...
Hey so I just wanted to use the BMI270 on the Thingy:53 and Polling the acceleration values seems to be working just fine. I wanted to use the DATA_READY Trigger. I am working...
Hi everyone,
In nRF9160 with ncs 2.9.0 I've problems when trying publish a MQTT payload bigger than 2700 bytes aproximately. In advanced I already was adequated buffer size...
Hi, I've recently acquired an nRF54L15DK, and started the development on BLE, I'm fairly new to Nordic's enviroment. In the last couple days I've been trying to build the...
Hi everyone,
I use the ble-app-buttonless-dfu example to develop my application.
I make a mutual authentication to be sure the device is connected to the right mobile...
Hi,
I am fairly new to BLE application development on NRF52.
I have a temperature and humidity sensor TH02 and I have interfaced it by making essential changes in TWI...
I found a function, sys_reboot() that apparently reboots the nRF9160. In order to use this function, what must be configured and what are the correct .h files?
Thanks
Hello,
I am trying to configure my nRF9160 v0.8.5 dk for current measurement and found out that SB 44 is missing on my kit. As the user manual suggest that in order to enable...
Dear DevZone team, I am using Thingy91 in NB-IoT mode because I am located in Germany. Last week I managed to connect it to the nRF Cloud by updating the firmware (thingy91_nbiot_legacy_pco_v0...
Hi,
I have multiple sensor data that needs to be recorded in separate files. This data is being collected in parallel. Using the FATFS xample in SDK 15, I am able to write...
Hello all,
I’m trying to connect my nrf51dk (board 1) with a CSR8670 (board 2) using GAIA services and characteristic.
On BOARC 1 i have implemented “Central HRS” beacause...
We made the test with your demo SDK on the board :
PCA10056 1.0.0 2018.46 PCA10056 1.1.0 2019.26
We modify the code to gate the trace ( see the attach file)
And the...
Hello team Nordic,
Example ble_app_rscs_c is working well with my pca10056, im using it to scan for advertising reports. To do the same with pca10059, im trying to merge...
Does the nrf52811 temperature peripheral do automatic linearity compensation? The product specification 1.0 says: " Linearity compensation can be implemented if required by...
I'm currently unable to build the asset_tracker for Thingy:91 on Segger Embedded Studio - using nrf9160_pca20035ns for the nRF Connect SDK Project
Do anyone have an idea...
Dear Team,
what is the way to do it in Zephyr?
I have a signal up-to 10kHz, what is the best way to keep the counter in the background?
Thank you and best
Oleh
In the getting started assistant App
When I run:
pip3 install --user -r zephyr/scripts/requirements.txt
I get this as the error:
However, when I run
pip3 install...
I am doing power consume estimation, need to know detail of RF activities, is there any way to get the total send/recevie bytes of RF? or just simple tx/rx counts? My project...
Based on nRF5_SDK_15.3.0_59ac345 at nRF52810
Bootloader = examples\dfu\secure_bootloader\pca10040e_ble\
Application,
Program Size: Code=36132 RO-data=5176...
