Hello, I’m trying to compile code for a u-blox C209 AOA Tag. I installed the nRF Connect Extension Pack and was able to build normally.
After adding some unrelated paths...
This stopped working for me... Error is the following
Command failed: git ls-remote --tags --heads github.com/.../sdk-nrf
fatal: unable to access ' github.com/.../'...
Hello,
After a lot of efforts I managed to autoprovision and autoconfigure my nrf52840 board (provisioning and configuring inside the software and not through external app...
Hi there,
I am trying to interface at25xe321d with QSPI but it always end up returning zeros. Please find attached code and dts file for reference. Thanks Moh
Hi,
We have a custom PCB based on the nRF9151 and nRF7002 for a tracking use case, supporting both indoor (Wi-Fi scanning) and outdoor (GPS) positioning. Our firmware is...
When version 1.0.0 of nRF54L15-DK evaluation kit will be available and how to distinguish the version when ordered from distributors like Digikey?
In discussion here:
...
-> How to transfer data from one thingy52 device to another thingy52 device. If i have 2 thingy52 devices, I'll send data to 1st tingy52 then 1st thingy52 device will send...
Hi,
I am trying to used the WINC1500 Wifi module with the nRF9160 DK but I am not getting any data back from the module.
I am using the module
https://www.microchip...
Dear Nordic Support,
I follow this SAADC example to calibrate the SAADC every SAADC_CALIBRATION_INTERVAL.
However, whenever the function nrfx_saadc_abort() is called...
I am running into a strange issue. I want the bootloader to start automatically when I power on the device and then start the application if there is no activity after 30...
Hi,
If I want compiler my project at specified locate, the only thing tat I need to do is following image? Is it right?
After I program this program into address 0x0001D000...
I am trying to make PN7150 work with nRF52840 using TWI Communication.
Problem : PN7150 gets detected with I2C scanner example when using Adafruit Bootloader and programmed...
When I run "pc-ble-driver-py/pc_ble_driver_py/examples/serial_port_enum.py" on armv5tejl GNU/Linux 4.2.6+ (32 bit) connected with NRF52 DK, it is throwing an exception
...
Hello,
I wanted to add additional info to my question https://devzone.nordicsemi.com/f/nordic-q-a/50846/secure-bootloader-timeout-not-working-on-s132-15-3-sdk-with-logging...
I am trying to save rssi data that I print to the command line to a .csv file.
In the ble_app_interactive example in the cli_m.c file, here is my code:
Without the following...
Hi
I have the Adafruit Feather nRF52 Bluefruit - nRF52832 board that I can program it using Arduino via Adafruit library in Arduino without any problems.
Now I have an...
How can I disable all code-optimizing in SEGGER ?
I build and modify some Nordics example-tutorials using nRF52832 and want start debugging.
Best regards Lennart Vedin...
Hi, I was using eclipse for the development of our board using the nRF52832 and when I launch the debug on eclipse, the program does not flash and this is the output that...
When using "nrfutil dfu serial" can it be configured to log all the bytes transmitted and all bytes received in a log file or on the console?
A colleague of mine is starting...
We have found what appears an easily reproducible bug in nrf_serial_read.
Reproduce as follows:
* PCA10040
* SDK 15.3
* SES
* Example project peripheral serial ...
Hi everyone,
I'm working on the nrf52832 using the SDK 15.2.0 with freertos and the application I am developing requires to save data on the flash while the BLE stack is...
Hi
When a GATT Table is created using the softdevice api, how do specify that a service or characteristic shall have a minimum key size of X so that if the current encrytion...
