Hello, I am experiencing issues with the current measurements taken by the PPK2 when using the nPM2100-EK to power a device. The current drawn from the 2.7V power source ...
I have been trying to get MQTT+TLS to work on the nRF7002 DK and haven't been able to get the samples to connect to the MQTT Broker.
Is there a working MQTT TLS example...
Seeing the failure below and wondering a couple things:
How did the device get into this state?
How do I disable AP protection? The Kconfig GUI seems to indicate that...
Hi all,
I'm working on a custom board based on the nRF9160 and using nRF Connect SDK v3.0.2. We’ve developed the board in-house and integrated the npm1300 PMIC as part of...
Hello,
For our emission tests in an anechoic chamber we need to be sure that the BT antenna is up and running. Of course we cannot connect via BT from outside the chamber...
hi support team,
docs says we can program 54l15 external spi flash ,please refer to : https://docs.nordicsemi.com/bundle/nrfutil/page/nrfutil-device/guides/programming_external_memory...
I'm using the IoT bootloader from NRF52 SDK 14.2. When the bootloader has nothing to do and starts the main application, the FDS calls all fail in the main application. When...
We're using QuantumLeaps and want to send a message each time a character is received on the UART command line interface transport layer.
Where in the SDK source code would...
Hello,
I have just purchased the nRF51 Development Kit and I am having extreme difficulty getting any of the sample programs to function.
There are the specifications...
Hi,
I am porting a NCI (Nfc Controller Interface) driver to the nRF52. One of the things I am struggling with is that, when reading from the device, the amount of data...
At first i have tried the simple uart code from nRF52 where i could send the AT commands properly and UART communication works fine between nRF52 and GPRS module.
Next...
I use a development board with nrf52832 xxaa, BLE demo from SDK works. But I created own board but with nrf52832 xxab(less ROM and RAM) and changed configuration in IAR project...
Hi,
I want to use hardware ECB encryption and decryption in 52840.I had tested the demo from nRF5_SDK_13.1.0\examples\crypto\nrf_cc310\aes\pca10056 . However,i can't find...
When using the APP_TIMER in SDK14 I am having a problem with the application stopping.
I was using the APP_TIMER to flash LEDs and watch for timeouts in SDK13. when porting...
in the sdk_config.h there are plenty of definitions, where "31" is used as a non-valid PIN value
This is destructive if you want to use p0.31
For example:
If one uses...
Hello. I want to use the same pin on nrf52832 for wake up and system off, however I have some issues, like sometimes it doesn't wake up or it is needed to press button few...
When I use sdk14.2 nRF52810 ble_nus_string_send to send data to a mobile phone android, the first connection is no problem, but disconnected again after connecting problems...
Edit: I'm using the softdevice S110, 8.0.0, Nrf51822 chip, Keil uv5.12
Edit #2: Added more detail and revised certain description.
What's the problem?
My program...
Dear partner,
1) Our custmer want the spec of S140, I cann't find that on the inforcenter. can you give me one?
2) By the way i want to know where is my mypage case...
I want to have every node carry a copy of the sensor data in every other node and pass these around on update.
Should I use ANT FIT or FS? What makes mores sense?
As the...
Hello,
How can I detect how much RAM is still free on the heap during runtime, without a debugger attached, just from within the application?
Cheers
Trax
