HI,
I am using the nrf_desktop sample in NCS V3.0.2, I want to buil with prj_release_dongle.conf , the setting
but build fail, I check the file Path: it should be F...
Hi:
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party repository within the SDK itself...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
I keep having problems like frequent disconnects (reason 0x08 = BLE_HCI_CONNECTION_TIMEOUT) and NRF_FAULT_ID_SD_ASSERT on my NRF52832 (tested with S132 v3.1.0 and V5.0.0-alpha1...
In the API file nrf_drv_twis.h for the nRF SDK, the definition of NRF_DRV_TWIS_DEFAULT_CONFIG looks interesting. The definitions for SCL and SDA pins are both set to the same...
Hello,
Is it possible to have 170 characters long device name somehow to the nRF52832 so that standard Android phones are able to see it without any pairing or any other...
In ANCS example (SDK 11.0.0)
I thought keys list distributed should be the same naturally until I see the code below.
ret_code_t dm_register( dm_application_instance_t...
I saw following code configuring about permission of charateristic value R/W.
it's in uart example of SDK 11.0.0.
static uint32_t tx_char_add (ble_nus_t * p_nus, const...
Hello
could anyone help me how to setup pipes for my characteristic, i need to recieve/transmit data to UUID of my characteristic, and recieve/trasmit to ClientcharacteristicConfiguration...
I have a ADC interrupt that occurs every 17ms and which copies the samples into a global static array, after which GivesFromISR to a binary semaphore so that the samples may...
please anyone answer for how to configure the digital input to make active the digital output in nrf52832? if give example program means it is much better
Hey!
I am working on NRF51822-QFAC, with the help of SDK 12.2 with the aim of scanning my bluetooth speakers and mobile phone.
For the same, I have loaded the project...
I want to change rx to tx mode and back after recertion my master NRF24l01 packet on NRF52 with esb, how to do it?
I tried this but it doesnt works:
void nrf_esb_event_handler...
Hello,
I am using nrf51822 and supply is provided through rechargeable battery. Please review my schematic and suggest changes if there is any.
Thanks,
Shailav
I used the following code to verify the working of the clock (at P04) of nRF24le1.
I used a 4.7K pull up resistor with a VDD of 3.3V, which was output from the nRF.
Note...
Hello,
I'm using nrf51822/s130/sdk12.1.0.
Before adding BLE code there's no problem in writing inner flash.
In main I just added below ble_app_uart codes(not modified...
