Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
Hi,
I found this code for adafruit BNO055 sensor on GitHub which is a Arduino code.
https://github.com/adafruit/Adafruit_BNO055
How can I import this on the Nordic nRF5340...
Hi all, I'm searching for a SPI example with NCS 1.8, I'm currently using nrf52840dk_nrf52840. I've looking at the drivers (nrfx_spi) but I still don't get it at all, so I...
Hi, I have a Nordic Thingy 91. I need it to save battery and transmit sensor data to Nordic Cloud on PIR external interrupt (if I could count number of PIR pulses that would...
Hi I am testing the Thread examples
I worked on SIMPLE_COAP_EXAMPLE in nrf52840 DK there it works fine while opening UART and enter to CLI commands and its working
but...
Hi again Nordic. I'm trying to write sensor data to the external flash continuously as there is not enough RAM to hold all the data required. However, the writing operation...
Hi,
I am using BL653 dvk to write an application for SPI, In my prj.conf, I added below parameters:
Now when I am debugging SPI master code, execution enters the file...
We are performing a preliminary power analysis with this device and have questions regarding the power consumption reported in the Product Specification. For example, the...
I've been struggling with enabling HTTP support on the serial_lte_modem. I've tried using various versions, currently I'm using NCS 1.8.99. I edit the prj.cnf to include CONFIG_SLM_HTTPC...
Hi,
I use nRF52840 and SoftDevice s140 (7.2.0). I use SEGGER Embedded Studio to compile a project written in C++. But lately I've been having trouble debugging. For example...
i've been test code from nrf51-app-button-example/main.c at master · NordicPlayground/nrf51-app-button-example (github.com) but not effect when presss any button.
I am new to Zephyr and Nordic. I onserved that to use variuos APIs it is required to declare in prj.conf file. But, where is the list and document of various commands woth...
Hi
I have a Nordic nRF51 as a Peripheral.
I have it open advertising until it connects for the first time to an Android handset.
When a connection is made it stays...
When I switch to any branch other than 1.8.0-rc2, I get the following notification:
"This workspace requires version 1.8.0-rc2 of the nRF Connect SDK, but it isn't installed...
I am developing a BLE Peripheral device using the nRF52805 and have just discovered that neither of the two SoftDevice packages offered for this chip have support for extended...
