Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
I'm trying to accurately measure our 3.0 volt coin battery (CR2450).
Our product consume low power (<50 uA) and we measure the battery voltage every minute.
We must...
Hello,
I've been trying to get through SUPL client library license signup process but I my request get denied every time.
I think I've done everything that is required...
I wrote a firmware on my dk52 and am advertising some data to the nRF Connect for Mobile App.
Is there any way on how I can copy or send the received data (service data...
Hi,
I have the following ouput using the throughput example:
Altered output format a bit to give me the same for local and peer.
But I was wondering why there is a...
Hi All,
I am running nrfConnect SDK v1.8.0 ad started a new sample LBS project. I ultimately want to have 3 devices, 1 being a Central and 2 Peripherals both running LBS...
Hi
Nordic Team
I used nRF5_SDK_17.1.0. I have a very difficult problem:
I now only want to configure an RX pin and no TX pin. Can the serial port receive data function...
After programming the a chip (52832) with hex files (including boot code, main app code, and softdevice), the chip jumped to the boot code so we need to do the DFU to let...
Hi again Nordic. I'm using the sparkfun level shifter: https://www.amazon.com/SparkFun-Level-Shifting-microSD-Breakout/dp/B01CF569VQ together with Sandisk 32gb formatted to...
I'm running into some rather strange things lately.
In debug mode, let's say I have two lines:
a[0] = 0;
a[1] = 1;
If I place a breakpoint at the 2nd line, and...
Hello,
I am trying to do my own i2c read/write from a sensor, and I followed the twim example available with the SDK.
When I build the project, I get errors wherever...
I am using Visual Studio Code to create applications based off samples, which I then build and flash to a nrf52840 DK which works great!
However, when using the nrf52840...
Hello,
I was working with the SDK 17.0.2 development kit and combined a few examples. When adding dependencies from other examples the path is entirely contained within...
Hi,
I have developed attached code for I2C communication with temperature sensor. The main function I2C_sample() checks whether sensor is detected by detect() and then performs...
When I try to debug my nrf9160 app through segger, it never starts. Hitting the pause button brings me to main.c in the mcuboot project, and it stops on line 214, Unable to...
Hello,
I'm evaluating both the Thingy:91 and nRF9160, trying to walk through the Getting Started Tutorial . Despite connecting my nRF9160DK to my Macbook (via an HMDI/USB...
