I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Dear Sir,
I'm using nordic's example codes above to tx and rx, but i can not get them working properly. the LEDs should light on the receiver side according to the example...
I have a strange issue on the nRF9160-DK board using the nRF Connect SDK, GNU ARM for GCC v10.2.1, built using makefiles.
I have two threads that both wait on a semaphore...
Hi,
I am trying to change the tx power of Zigbee using the following APIs :
1) zb_set_tx_power(0x32); 2) nrf_radio_txpower_set(NRF_RADIO_TXPOWER_NEG12DBM); 3) nrf_802154_tx_power_set...
I am currently using a nRF52-DK to follow the connection between two external devices. I run the sniffer and start/stop the sniffing via Wireshark. When I start sniffing,...
Dear Team, I face Following error with example downloaded from Github,
error 1) Output/Release/Obj/saadc_pca10040/ses_startup_nrf_common.o: in function `InitializeUserMemorySections...
Chip: NRF52840
Firmware platform: Wirepas V5
Hello!
I am now writing firmware for a product based on HW&SW mentioned above.
It is powered by battery and sends data...
Dear Sir,
please do me a favor to reply on my following question.
our project is a keyboard which we expect can work on both ble and 2.4G. we will use other brand of of...
Hello
I am using nrf52832 and sdk v17.0 I recently succeeded in controlling several ws2812 LEDs through I2S. And now I'm going to combine these codes with the others.
...
Hello,
I'm trying to get the SPI drivers working in slave mode. I have tested my master (Atmel L21) on an Arduino and I can see my message clearly. I'm trying to get nRF52833...
Hello
I want to access to the buffer to see what I am transmitting for then change the data to transmit to be able to verify, also I want to know where I can find de Kconfig...
Hi!
I have a custom board with a NRF52840 and some extra sensors for my application. I'm trying to comunicate with one SPI sensor but I have a little extrange behavior....
Hi,
I am trying to create a combined Bootloader + Bootloader Settings + Application hex file to flash the same into the devices during the production.
Bootloader Project...
i write 40bytes to flash 0x74000 and read 0x74000。i find it actually use 160bytes. I try to write a different number of bytes, it actually use 4*(write bytes)
this is...
I wonder if I can use spi1 or i2c1 on nrf9160. I use the 9160ns board configuration but non of my configs work for spi1 or i2c1 works. If I change it to i2c2 or others it...
