Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I have updated to SDK V1.2.0 and the AWS FOTA fails to get an ip address. My version 1.1.0 AWS FOTA still works.
See settings and outcomes below
For v1.2.0
and...
Hi,
I have an application on NRF52840. I'm able to connect successfully to mobile devices, with min connection interval of 7.5 and max of 30.
However, when I try to...
Hi Nordic Devzone,
I am using the simple BLE blink peripheral example that simply advertises and blinks an LED. I am using the ble_app_blinky_pca10040_s132 example found...
The Interface MCU on my nRF52-DK (PCA10040) broke, I replaced it with the same part number (got it from the BOM) and now I am struggling to program it through the JTAG port...
How does one get Mesh Network Id and Mesh Network Name on a provisioned device?
So far I have looked through the Mesh SDK API documentation, but was unable to find an answer...
Hello all,
My project based on NRF52832 SDK13 has some bug I trying to solve. Some users of my product very rarly faces with problem of constantly rebooting NRF52. After...
Hi,
I am trying to perform ADC conversions controlled by Timer with minimal manual interaction. My goal is that every 2 seconds, the ADC takes 10 samples in quick succession...
I have a project using nrf52840. The nrf52840 communication with a nbiot mcu using uart port. In my project the nbiot download the firmware from server and send the firmware...
Hello,
I'm using 2 sparkfun nrf52840 boards. On the central board I'm using ble_app_multilink_central ( trying to integrate ble_app_uart_c example ) and on the peripheral...
it says "The SAMPLERATE timer mode cannot be combined with SCAN mode, and only one channel can be enabled in this mode." , simply why ?
When we set scan mode , and when...
Hello guys!
We want to configure ADXL362 accelerometer on Thingy:91 board to wake up nRF9160 SiP via INT1 external interrupt. For that purpose, we need to properly configure...
Hi
I am sending data from PC to nRF52832 via the UART interface using ble_app_uart example. I am performing some operations on the data and sending data via Bluetooth. I...
See the product named "HZX-51822-16M04 Bluetooth 4.0 Low Energy Module" I need some information regarding it listed below
In this nRf5182 is the main chip soo.
1. How...
Hello,
we have a product with a firmware based on SDK13 with a serial Bootloader SD 4.0.2 on it.
Now we have to update those Devices to a new Firmware based on SDK16 with...
