Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
Hi,
For my project I'd like to be able to remove GATT services/charactertistics. Is this possible? I can understand not being able to remove single services, but is it...
Hi
The application I'm currently working on has three debug settings:
DEBUG preprocessor symbol
Optimization level 0
NRF_LOG at debug level (using RTT)
...and...
On my custom board I have a button BUTTON_1 in between supply voltage (Vbatt = 3V) and input on nRF52832 - therefore input will receive 3 Volts directly.
I have configured...
Hi,
I am developing a code in which, among other things, when a button is pressed, a led turns on. In the same button handler, a timer is started to turn the led off a bit...
I'm trying to evaluate throughput performance of our BLE application which operates in conjunction with the Apple platform. I would like to know if there is a way that I can...
I created a system some years ago that worked the way as the title suggests using classic bluetooth, and a cheap chinese module (HC-05) with custom firmware. Now I want to...
Hello!
I'm having some problems with Keil. It does not seem to have the board (52DK / nRF52832) installed. I've installed Keil 5.25, and in the pack installer I've added...
Hi to all,
i am developing a device with nrf51822 soc, i want to read some data from flash storage of nrf51822 then forward it on ble, i implemented a code for this job...
hi,
I used nRF52932QFAA ,SDK14.2 uart bootloader.it works well with softdevice loader 5.0.0.But when I download my app(without softdevice),it cannot work.
Flash composed...
Hi!
I am using SDK15. I am developing application which is mainly based on ble_app_uart (with NUS) service. NUS service consists of two characteristics: - RX Characteristic...
What Bluetooth SIG fees are required for a product that includes the Nordic nRF52840 chip?
What about for a product that includes a 3rd-party Bluetooth module (that contains...
Using the S132 soft device on an nRF52 DK and calling the sd_flash_write function always produces the NRF_ERROR_FORBIDDEN code. The following is the line believe is causing...
Is it available indoor positioning service implementation (asset tracking etc.) or demo for nordic thingy52 modules or other NRF uC based on the BLE Mesh protocol ?
If any...
