We are having a slight issue when we are trying to update the DFU. The original version had this setting for the data reserve:
#ifndef DFU_APP_DATA_RESERVED
#define DFU_APP_DATA_RESERVED...
Hello!
I am working with the example mpu interface projects located at the following repo:
github.com/.../nrf5-mpu-examples
After converting the Keil projects to...
I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
I've added a custom service for transferring data. It shall contain one characteristic that will notify when data is available, and the other should be a long read characteristic...
I recently got involved in a project where I am deploying a ble based mesh to understand and monitor bridge vibration patterns. I have been through nRF's mesh capabilities...
I am using the Arduino Primo board.
I have multiple beacons that advertise at a set interval.
All beacons have the same Device_name.
The Arduino Primo board scans for all...
Hello there. I just recently started programming using the nRF52832 DK, SDK14.1.0 and SoftDevice 132 v5.0 . I tried to follow this tutorial on Github: github.com/.../custom_ble_service_example...
I am using a power profiler to measure the timing of my program and I found something wrong. So I tested with a simple pure timer.
So first I set the timer during to 300ms...
I just spent 2 hours chasing BLE bug after upgrading from s132 v3 => v4.0.2
I added a call
// Configure the maximum ATT MTU.
memset(&ble_cfg, 0x00, sizeof(ble_cfg)...
I couldn't use nRF Connect (BLE) under Linux, after updating the FW, it tries to open /dev/ttyACM0 but fails to do so.
Not a "permission" problem: the user is in uucp...
Hi,
I'm unable to compile the OpenMesh example application. I've modified the make file with correct paths. However I'm getting the following error. Can you please help...
I have a NRF51 talking through the UART to another uC, and I'm trying to log messages through Segger RTT. Everything works normally until I start to send some data through...
If SEGGER_RTT_CONFIG_DEFAULT_MODE is "BLOCK", the program won't start without RTT attached - at least for me... is there a possible solution?
I mean, technically it makes...
hello ,everyone
I was confused by a PWM problem for a long time , on nrf52832 SDK13 ,i wanna change the PWM duty cycle every period ,but now i find can not change it at...
Hey dear Devzone,
I am trying out some Thread and BLE dynamical examples on my nRF52840's but running into some problems using the " ble_thread_dyn_mtd_coap_cli " example...
Hello nordic dev community,
I am completely new to nordic products. I attended one of the conference and got more information regarding developer zone and info center....
Hi,
I am wondering why the ccm library uses the software aes encryption. Is there anything wrong with the hardware encryption so that it should not be used?
Marius
