Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I have previously bought a Evaluation kit, (now obsolete) and registered with it. I have also designed a new custom board with version 3 silicon, but I cannot download v8...
Hii...
Am working on S130 demo example. While going through the code i found that code is implemented in polling method. when i compared with s110 example i found that...
How to flash SoftDevice and Bootloader (OTA enabled) to nrf51822 by CMSIS-DAP programmer?
For instance: I did cmsis-dap programmer with mbed code form github.
Can I do that...
hi,
I am want to communicate with nr52 dongle via serial. The dongle periodically outputs data which I read.
The problem is that is the python connect in the middle...
I'm looking for the set of command line interface for the bluetooth nRF51 sniffer program, such as to list the device available for sniffing. for example the L + . and then...
In the system on low power mode , how and where to change the startup time t1V7 for 1V7 regulator and startup time t1V2 for 1V2 regulator for better power optimization. And...
I know this was asked before, but none of the posts address my problem. There is a similar thread , but the issue on that one was that the softdevice was not being used. I...
Hi all,
I'm implementing a Bootloader with the source code provided no the website (Windows C# app, nRF24LU1 station app and nRF24LE1 device bootloader/app). Everything...
Hello,
When using the nRF Master Control Panel I see other Beacons with "Complete Local Name"... I am building an iBeacon but have not found a way to set the name and have...
The following thread talks about CPU unblocking during connection intervals.
devzone.nordicsemi.com/.../
How does this feature affect BLE Radio Notification? Do...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
Good Moring engineers.
I just got nRF24LE . I am wondering the timer2 only provide 2 seconds long period ?
I want my project nRF24LE sleep as long as possible , at less...
I am using an RTC for other purposes that exposes a buffered 32kHz clock. I am considering using the buffered (rail-to-rail) for also the LF timebase of the nRF51. The drive...
