Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I have an nRF54L15DK and a custom-designed nRF54L15 board. These two boards use different pins for peripherals. The NCS version used is v2.9.0. I compiled a Matter project...
Hello, Not sure if this is the place for these questions, but here it is:
I've configured new board, and when I try to debug using the ncsconnect vscode plugin (linux...
Hello everyone,
I need some help in understanding and optimizing current consumption profile of nRF9160 in LTE-M cellular connection mode.
nRF9160 is implemented in...
I initially tried Segger Embedded Studio for ARM and I clicked on connect to J link device, an error occured. I wasn't sure at that time. Then I used the nRF CONNECT for desktop...
Dear Nordic-Team,
i have a nRF9161-DK Evaluation Board. On this Board the Firmware of the Debugger SoC (nRF5340 / U3) is not working. I tried to flash another Firmware onto...
running Windows 10 Pro 22H2 and using j-link v9
i tried to read firmware from nrf51822-QFAB by using " nrfjprog --readcode dump_nRF51822.hex", but it gave me an error...
I have implemented a program that sends an image's .HEX file through our custom software. The data is received and parsed by an application running on an NRF5340. The relevant...
Hi all
I am using the bluetooth central sample from zephyr. I can read the addresses of the devices but I would like to read each specific device's advertisement data. So...
I have the following settings in my prj.conf:
and getting the error
CONFIG_FLASH_MAP was assigned the value y, but got the value n. Missing dependencies: FLASH_HAS_DRIVER_ENABLED...
SDK:nRF5_SDK_17.1.0_ddde560
example: ble_app_multilink_central
softdevice: s140_nrf52_7.2.0
PCB: PCA10059 as Cental
My peripheral device's mac is 00:96:81:16:E0:9F...
Hi, I'm trying to use BLE OTA with an external memory due to my application is too big to do it only with the internal memory. When I use OTA config with internal memory,...
Since I am developing a lot for the nRF51822, I heavily relied on the old reference pages for said chip, like SDK 12.3.0 Reference .
Now they seem to be gone.
Could...
Currently nRF54L15 is being matched with LOW Q circuit and unipolar antenna. Because low Q circuit takes a lot of components and time when designing hardware. So I can remove...
We are trying to use extended BLE advertising with a nrf5340dk and are experiencing problems when trying to connect to an android phone (Android 13). Using legacy adverising...
