Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi,Nordic Friends,
I'm using nrf5340dk,and my project need commnunicate with NB-Iot Modem over uart.Now, I found the dirver that i can use directly.But When I configed the...
Hello All,
My company has recently decided to switch to Nordic at the direction of one of our suppliers. We are very impressed with the devices offered and the available...
I use a nRF5280 DK to get DFU working.
I connect to the DFUTarg, Click the Start Secure DFU icon, select my app_v3.zip file, click Start DFU
I get this error during...
Hi there!
I just switched from the GPS Library to the GNSS API.
The problem is, that we never get the timeout event NRF_MODEM_GNSS_EVT_SLEEP_AFTER_TIMEOUT . Basically...
Hi, I took a look at the low power comparator example from the Nordic SDK and test it with my nRF52-DK and I found out that the comparator isn´t triggering when I set the...
Hello, I have a problem with the I2C peripheral on my nrf53840. I enable i2c driver on my project and read sensors on the bus. Everything is OK. Then when with Power management...
Hi Nordic,
I am working with the s140, sdk 15.3. My application is a central that should connect to a device that has several services. As soon as the connected event is...
Hello,
I am using nRF Connect for Desktop 3.7.1 with a nRF52840 USB dongle for testing purposes.
In the Bluetooth Low Energy 2.5.3 application I deselected the "Auto accept...
Hi,
I'm using Nrf52840 to connect to a Mobile via BLE.
I'm advertising to start connection, and after bonding, I can start advertising with whitelist in order to connect...
When adding this line to codes from an article here control reaches
Example used is ble_app_hrs_pca10056_s140 on nrfDK2 , sdk 17
==================added to advertising_init...
Hi,
I'm trying to use Thingy91 as a gateway for collecting data through BLE (from other thingy52s) and send it to Azure IoT Hub using LTE, but the current sample code only...
Archlinux
Visual Studio Code: Version: 1.58.0-insider
nRF Connect: v2021.9.98
I installed the "nRF Connect" extension in vscode, and went to look into a problem I was...
Hi,
I'm currently testing LPCOMP with one of our nRF5340DK boards.
The power consumption of the LPCOMP seems way too big (around 140µA) once enabled with this conf...
Dear Nordic Engineer
Our customer uses NRF52832 to develop a computer remote control pen. They are based on the keyboard example in the 15.3.0 SDK. Now they encounter some...
I have a working (hand-wired) prototype that connects to the internet without any problem.
Now I have made a PCB to replicate the same thing and loaded the same software...
