Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi,
I have developed an app using OTA DFU support. Soft device used is S112.
is it possible to update Soft device through OTA DFU?
what is the max size of the image...
Hi , How can I connect arduino nano 33 ble with the application NRF Toolbox using Bleutooth when I program the arduino with segger embeded studio .
Please I need your help...
Hello:
After the nrf52 lost connection with the phone, should it go to the Directed mode of just start normal fast advertising. And what the differences between them?
...
Hi,
I just used the nRF Connect Toolchain manager to install the NRF Connect SDK. Then, the Segger studio keeps popping this error when I try to open a project:
And...
Hello,
From the nrf91dk datasheet, a stackup is provided. Because it looks custom, and I'm having a hard time finding a manufacturer that can do that stackup. What PCB...
hi，
I read the data manual of 52832, but I have some questions about the following parameters, like CM_FLASH,CM_FLASH/MHZ,CM_FLASH/MA,please explain it in detail and what...
Hello ervery one,
I am doing development on NRF52840. I have a problem as follows looking forward to your guidance.
I need to jump to Application 2 (address: 0x32000)...
I See in the discussion that I can see I/Q for AoA.
I see this examples "direction_finding_connectionless_rx" on zephyr I Think that I can start debug using the data from...
I want to transfer a few bytes of data between two NRF52 modules.
I have checked out the BLE Blinky and NUS example and understand the gatt client and server ideas.
My...
Hello.
I am using SDK version 17.0.2.
The example code uses nrfx_spim . Target board nrf52832
The nrfx_spim project confirmed that 10040 did not exist, only 10056...
hello,
in the case
Case ID: 227777
https://devzone.nordicsemi.com/f/nordic-q-a/46439/turning-services-like-hid-on-off-without-disconnect/309149#309149
In the...
I've got a Thingy:91 plugged into my computer and can see its USB terminals (/dev/tty.usbmodem143101 and /dev/tty.usbmodem143104). I can also see the "ZEPHYR USB" volume and...
Good morning,
I am working on nRF52840 DK, using nRF5 SDK.
I am trying to communicate using SPI.
However, I found out that the function nrf_drv_spi_transfer took 10µs...
