I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
HI ,
My environment:
nrf connect sdk
nrf5340 dk
segger studio ide.
could you please provide me timer example code for nrf5340 board.
Thanks & Regards,
...
Hi,
I am using an NRF 51422 DK, SDK 12.3, and Soft Device S130. I am also a beginner to development with Nordic Products, and RSSI collection in general. I am using the...
SDK: 17.0.2
IDE: SES
nRF52832 module
Hi!
I have a nRF52832 based custom board operating on battery power. I assigned a variable to the non_init section in SES and...
Hey!
I have an isp1807 test board, which uses an nrf52840 chip, and an isp1p807 programmer (ISP130603E). Currently, my code is written using the nrf52 sdk v17. When I am...
Hi, I'm using nRF9160 as host and nRF52833 as a controller with NCS 1.5.0 SDK. On nRF52833 LPUART sample runs, I have added needed configurations for extended advertising...
Dear All,
I am working on interfacing BME680 with nRF52840-DK board. I got the output for Temperature, Pressure and Humidity but not getting the output for Gas resistance...
What should be considered for choosing a chipset? the followings are in my mind. Could you please tell me if I am correct and if I should consider anything else too.
1)...
Hi guys.
I flashed a uart-dfu Bootloader(SDK-location\nRF5_SDK_15.0.0_a53641a\nRF5_SDK_15.0.0_a53641a\examples\dfu\secure_bootloader\pca10056_uart), when the program run...
Can you, please, point me towards documentation and (if available) samples of mobile app that would allow me to commission and then interact with devices in RF52840-based...
Hi everyone,
So currently, i am working on a project relating to sending some message from one router to another. I found out that there is a function to create your own...
Hello everyone,
I've been struggling to use the Bluetooth UART example and the RTC2 module but so far I haven't succeeded.
Either I have Bluetooth, or RTC2, but not both...
Hello -
I have created a project with both a SoftDevice S132 and nRF Crypto libraries. All has gone well so far. I am now trying to implementing RNG, following the example...
The prototype I was working on has a nRF52832 on it and for some time it was working fine with the Segger Jlink base. However today I started to try to use the low power modes...
Hi,
I am using "TWI Sensor" example(SDK v17.0.2) as reference in our application. For multiple bytes transmission this is how I defined in "nrf_drv_twi_tx".
Here is...
