Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
I'm trying to get LPCOMP working on Zephyr - I have used the vanilla NCS sample as a baseline and have set up the event handler and the init function.
The problem is that...
Hi,
I recently bought a couple of HolyIOT nRF52840 modules for a personal project (building a keyboard). I also got a JLink Edu Mini to flash/debug it. I am able to successfully...
Hello,
I've seen when ADV interval is near than 1 second, the sniffer cacth the same adv twice in diferent channels, but if the adv interval is near to 50 ms the sniffer...
Dear all,
I managed to implement custom firmware using Nordic proprietary protocol (both 1 and 2 MBPS) on nNRF-52840-DK. I would like to know if some spread spectrum tecnique...
A plain question : we are using the BLE stack with FreeRTOS based observers.
Is it possible to send to some observer an application defined event from some other FreeRTOS...
My project is a health thermometer using nRF52833. I am working nRF5 SDK 17.0.2 with GCC make complier.
I start with the ble_app_hts example and it is working fine. I try...
Hi,
I observed that in some cases SLM waking up from idle mode (at#xsleep=0) has CFUN reset to zero, even if I run AT+CFUN=1 before at#xsleep. Presumably that happens when...
My current implementation is based on light switch example and I am currently using nrf52832 kit with Mesh SDK v5.0.0. I have a mesh network setup with a client and two server...
Hello,
I am using nRF52833, nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8 and SEGGER Embedded Studio for ARM 5.34.
I have imported some multiprotocol examples and trying...
I have an nRF 52832 running the SDK 15.2 with s132_nrf52_6.1.0_softdevice as peripheral and a Dell XPS 13 9350 laptop with the integrated bluetooth 4.1 module (Dell Wireless...
Hi,
can you please tell me in what cases I get this assertion?
SOFTDEVICE: ASSERTION FAILED, PCxxx: 0x12D7E
It seems to happen when a connection is active, timeslot...
HI All team Members !
Hope you all doing well ! . Yesterday , i have tested the two SDK's "ble_app_uart_c" as a BLE Beacons Scanner and "ble_app_beacon" as a BLE Beacon...
Hi,
I understand that the CoAP Client sample is configured for a public URL (californium.eclipseprojects.io) in the Kconfig file. I wanted to ask, how the KConfig file...
Hi,
I am trying to perform DFU over mesh network. I am following the steps as given in this .
I could achieve the steps from 1-6. But while running the command for Transferring...
Hi,
When running FreeRTOS I'm not able to use the NRF logger module once the task scheduler has started.
I have a low priority task that flushes the logs but whenever...
