I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hi, i'm trying to load the aws_iot sample and I'm running into mqtt_connect, error: -95. Based on other posts, it seems my certificates might not be properly loaded. As far...
I am building on a BLE DFU project which already has a NRF_FSTORAGE_DEF for allocation of non-volatile data used by DFU. I want to add another instance of NRF_FSTORAGE_DEF...
Hello,
I am using the modem callback:
To check if the modem is connected using the following code:
However, as far as I understood this only indicates that the modem...
Respected Sir, Mam
I am Noel Joe Riju Antony a student of Amity University, Noida, India pursuing a B.Tech in Aerospace engineering. I am currently working on a CW radar...
Hi,
I've got a Thingy:91, which I've spent a lot of hours in understanding the different samples. I want to be able to send GPS information to my Azure IoT hub device...
Utilizing SDK 15.2 and Softdevice S132, when debugging with Segger Ozone and starting from main or after triggering a reset to restart at main an ERROR 8 [NRF_ERROR_INVALID_STATE...
Tried running android app in debug mode, but I could not see any data on the crash.
tried resetting the board a few time and re commissioning.
followed the guide to set...
I found a lot of posts with this warning/error, but I could not find a fitting solution among them.
in my case, I copied the `peripheral_lbs` project to another folder,...
Hello
I have a few questions regarding the "ble_thread_dyn_mtd_coap_cli" example:
In the "main.c" file, I notice that you have created timers to call "sd_ble_gap_conn_param_update...
Hello.
I have a custom board with a uBlox BMD300 on it. The BMD300 is based on the nRF52382. The BMD300 had a pre package firmware in it that acted as a BLE UART bridge...
Hi all,
I am using the python bindings in recent weeks to development a BLE scanning device and have found the python bindings very useful for getting the kit up and running...
On MacOS Big Sur (11.2), trying to get started with nRF5340 samples, but getting create_nordic_project.py failed (1) errors.
I installed manually using the nRF Connect v3...
We are in the evaluation phase of a technology that is planning to use sound to transmit data between phones and devices.
We are currently using Quiet open source library...
Hi Team,
We are using the nRF52840 DK for one of our project, as part of that we are using the RNG functionality with CC310 Library.
When we call this "CRYS_RND_GenerateVector...
