I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello Team,
I want to use scheduler to schedule two tasks i.e task_1 and task_2. The task_1 and task_2 are as follow:
void task_1() { printf("Task 1 ran"); }
void task_2...
Sorry this might be a stupid question.
We are evaluating some modem to develop a IoT device, NRF9160 comes up to our list as its tiny size.
In the design of IoT device...
I wants to use break point in project but when i set break point then 4 or 5 times working after that goes to NRF_BREAKPOINT_COND, I am using nRF52832. so guide me where is...
We are using NRF52840 and we have a watchdog timer connected to reset the Nordic, if needed. What is the minimum and maximum time need to insert a reset on Nordic?
thanks...
I want to transfer sensor data to a raspberry pi using the in-built USB on nrf52840. The example codes have the following classes: CDC_ACM, Audio, HID and Mass storage. I...
Hello,
I am just curious wether there are any specific recommendations or requirements for the package-sizes of capacitors/inductors listed in the BOMs of the nRF52840-reference...
Hello,
I am working with the latest version of nRF52 SDK 13.0.0, when I was implementing my own bootloader application, I tried to start an app timer in my code to invert...
Hi there,
Could you please tell me the exact part number of nRF9160 and nRF52840 on Thingy: 91?
I cannot find the specific information even though I looked through the...
Hi All,
How many nodes can connect to a node in ble mesh network. I go through code in ble mesh, but i did't found the answer.
Can any one please tell me.
Regards
...
We have an application using SDK for Thread 4.1. The application requires sending large custom commands over CLI.
We increased the size of NRF_CLI_CMD_BUFF_SIZE in sdk_config...
Hi, I am using the nRF connect app to test the BLE function on my code. I am able to scan the device and Service UUIDs just fine. However, when I click on the "connect" button...
Hello,
I have been trying to implement the tinycrypt ECDSA algorithm for our product. I had sampled the implementation in a sample project with ECDSA being the only implementation...
Hello I am working on an application which is based on the ble_thread_dyn_mtd_coap_cli_pca10056_s140 example. I then used the ble_app_rscs example so that I could add Bluetooth...
