Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
I'm trying a new device based upon the nrf52810 and it won't run past sd_softdevice_enable - it goes to the assembler window and halts. The device does have a 32kHz xtal and...
Hello,
I was reading some SDK 15.3 code, there's something like this:
__STATIC_INLINE void pwr_mgmt_sleep_init(void) { #ifdef SOFTDEVICE_PRESENT ASSERT(current_int_priority_get...
Hi all, I'm developing nRF52840-DK to use it as an central device.
Base example is usbd_ble_uart: I'm going to communicate with peripheral device using BLE, and control...
We have a product that uses the nRF52840. We have seen that very rarely, unexpected resets happen with the reason being OFF. We have yet to encounter this issue in a lab setting...
I'm using the SPI manager to talk to an ILI9342 graphics IC. I need to toggle an IO line during a transaction or in between transfers. For the first byte the line will be...
I am trying to enable DFU over USB with the nRF52480, while keeping the possibility for Serial communication. I got a working example with both separate, however when I try...
It's my mistakes.
1.I want to measure temperature from DS18B20,but I don't confirm the capable of the pin - P0.05.Because it's Analog ，but DS18B20 is Digital.
2.I set the...
Hello, I'm getting started with a nRF52832, I've got the SDK 16.0 installed and what I think are all the latest packs installed. I try to build the examples\ble_peripheral...
Hello everyone.
I'm trying out the "Zigbee Multi Sensor Example". infocenter.nordicsemi.com/.../zigbee_multi_sensor_example.html
I have 2 nRF52840 devices.
I wrote the...
When my program starts, I set up a watchdog timer for 100 milliseconds and I start a repeated app timer that runs every 90 milliseconds to feed the watchdog. I use the app...
I'm trying to send data via UART from a NUCLEO-F401RE to the nRF 52840 DK. But the data I send is not comming through correctly. For example when I send 3 the nRF prints 32...
I have an existing product to which I need to add SPI to get Wifi compatibility. Basically the Nrf52 is acting as central and passes BLE events on to an ESP32 with Arduino...
Hi.
I have nrf52840-dk board. i tried the UART example from the peripherals directory. it works with the default, if i open a console on /dev/ttyACM0 and on /dev/ttyUSB0...
Wanted to ask if there is any example on configuring the GPS into single shot mode.
I know the asset tracker can operate in continuous_mode and continuous_power_saving_mode...
I am attempting to use SDK15 with the nrf52832 to communicate with multiple sensors over I2C. However, in the twi_sensor and twi_master_using_nrf_twi_mngr examples, as well...
