HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
I have a question about Makefile template used in all samples in SDK12.x
What is the sense of:
$(foreach target, $(TARGETS), $(call define_target, $(target)))
-include...
On the NRF52810_PS page, I find UART is exists,
But on the sdk_15.2.0, NRF_UART_Type is disappear at nrf52810.h.
So I can't call any nrf_uart_xxx functions and UART...
Dear All,
I know similar questions have been asked before but I have read around quite a bit and I couldn't find an answer to my specific problem.
I have a ble application...
Hello All,
I am working on the simple advertising example.
I am using SDK_V_15.3 and NRF52 DK board.
I want to create a timer for on / off the advertising repeatedly...
Hello,
I have successfully flashed and run the mqtt-simple example from the nrf samples with the default configuration.
If I run it 10 times in a row, the getaddr with...
Hi.
I struggled to migrate ble blinky example of nrf5 (nrf51422) to nrf51822 using KEIL (SDK5 v12.3) but failed
Here are what I tried.
Firstly, I changed target device...
Hello,
I want to create a program for communication and control between the NRF module and the desktop. I followed the instructions Installing from https://github.com/NordicSemiconductor...
Hi!
I'm working on a toy based on the nRF52810.
The BLE requirements are very low:
- Peripheral only
- 1 link only
- No bonding/pairing, no encryption, no whitelist...
i can create three service each with one notifiable characteristic. i am using nrf connect to test if it is work and i am able to send data through UART Rx and then enabled...
HI,
I'm use nrf51822 and SDK 10. I want to use APP_ERROR_CHECK function to show error msg, I did also enable LOG function to support this, but it do not work.
here is...
HI everyone!
My case:
nRF52832 + toolbox on iOS and Android
I have device pre-programmed using seeger with settings:
Next I want to make DFU update using .zip...
I am trying to receive data from GPS L80 with the nrf52832 board but I am not able to receive anything. I connected the Rx of nrf52832 with GPS and vice versa. I also connected...
Hello, I'm trying to get manufacturer specific data from peripheral, but I don't know how to do this when the peripheral is using extended advertisement with LE Coded PHY...
Currently, I am trying to create a UART connection between the nRF52840 Dongle and my PC. I am working with the usbd_ble_uart example found in the dongle SDK. I managed to...
Hi,
I am using nRF52840 Preview DK with SDK v15.3.0 and Softdevice version 6.1.1
I modified the Blinky peripheral code to advertise over Coded Phy, this code is working...
