Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hello, my custom board is using pin 09 to communicate through uart. I want to check that uart is working on this custom board. First, I tried to create a simple uart application...
I am using NCS v2.8.0.
After successfully running the headset example with one gateway, one left channel receiver and one right channel receiver am trying to get the Auracast...
I spent quite some time trying to understand why I was getting random network disconnect after a totally fine CEREG notification, like in this log:
It turns out that inside...
Dear Nordic:
Light bulb project support 52840DK, can light bulb project support 52840 dongle? I have not found dongle option in l ight bulb boards folder, only find nrf52840dk_nrf52840...
Hello. consisting of nrf7002 + nrf5340, I'm going to do battery management and power management of a circuit that operates up to a small coin electric motor at npm1100, and...
Hi,
I am encountering an issue with the BLE connection on my nRF5340 DK. When I attempt to connect the device to my PC, the pairing process takes a significant amount of...
Hi,
I am implementing a BLE central that is based on ble_app_uart example using nRF52833 with a soft device version 7.2.0.
I have noticed that a single packet download...
Toolchain v2.70, SDK v2.7.0, VS Code, Windows
I am trying to enable the watchdog in my application, and I can successfully locate the device node and add a timeout, but...
Hi,
I am trying to figure out a way to update the toolchain and SDK for an nRF Connect for VS Code installed on an offline machine, without much success.
From https:/...
Hello,
I am working with the NRF9151 DK on DECT NR+ and I want to change the subcarrier scaling factor and subslot value in the hello_dect example. However, I am not sure...
NRF Connect SDK (v2.8.0), VS Code, NRF52840
Hi, while reading the Zigbee documentation I saw the following note:
"Support for Zigbee R22 has been deprecated in nRF Connect...
I am simply trying to build the hello world (and blinky, results are the same) with NRF-SDK 1.8.0 - it's based on Zephyr 2.7, which is the LTS release.
Target board is 5340...
Hi,
We are planning a new project that needs to use very low power. Since relay mode uses more power than simple node, can we turn off relay mode on all nodes until an event...
Hi, I am developing BLE beacon application on the nrf52820 soc which has limited Flash resources. I want to have the FOTA through BLE abilities built in to enable firmware...
Hi! Can you please help me identify what is causing this issue and/or provide more info about this:
[00:04:23.038,330] \033[1;31m<err> bt_sdc_hci_driver: SoftDevice Controller...
