nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
I would like to source a compact BLE board to act as a lock controller developed with with a matching transceiver for use in a fob and an app.
It would toggle the pio and...
SETUP:
2 x NRF54L15 DK initiator/reflector sample (as of 4/8/2025) Major RTT settings below - RTT (BT_CONN_LE_CS_MAIN_MODE_1) with 1M phy, 32 bit random RTT (will add settings...
I am working with nrf52840 dongle, details on the antistatic cover are( nrf6829, 2.1.1, 2024.02). I am trying to flash it using https://github.com/adafruit/Adafruit_nRF52_Bootloader...
Hi all,
I'm facing a challenge with efficiently transmitting high-frequency sensor data over BLE.
I’m sampling sensor data via SPI from a sensor capable of outputting...
Dear Team,
I am attempting to provision my Thingy91 device to AWS IoT Core using Fleet Provisioning with the Claim method. I've been closely following the instructions in...
Hi everyone,
I'm experiencing an issue with my nRF54L15DK board.
When I build the OpenThread CLI sample with the /ns configuration, everything works as expected. However...
Hello, I am working with a Seeed XIAO nRF52840.
I'm able to get an average of 500 uA in SYSTEM OFF mode. However, for this application, the current consumption during wake...
Hi guys, With v2.8.0 sdk, L4_e3 code ( academy.nordicsemi.com/.../) works with nrf52833dk. We have a custom board that we designed. Here, nrf52820 chip is used. I can compile...
Hi,
I have thingy:53 and I have damage to the sw2 pin and I am unable to enter the DFU. I lost two tiny pieces that go just above the one in the photo and not even...
Can some one describe how this is supposed to work:
https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/samples/mpsl/timeslot/README.html
I would have expected to see...
Hi,
I wonder if anybody could help me? What is the best way to close down the nrf9161 so that it reconnects quickly after powering back up again?
I'm running Zephyr 2...
Dear Nordic Support Team,
In the datasheet of the nrf9160 (nRF9160_PS_v2.2.pdf) the VSS pin appears in the section 6.4.5.1 GPIO Electrical Specification, but I cannot find...
I am preparing to make our first firmware release on our custom board, which is equipped with the nRF9160 SICA B1 , modem fw version 1.3.4 . Our application is based on the...
I've been running into a lot of issues where a change in the configuration for the application results in an answer that basically states:
"You're supposed to add this configuration...
Hi all!
I'm wondering why the VS Code has option to create a new board for the nRF5340-QKAA only?
I have on hands the nRF5340-CLAA and nRF7002 chips which I'm going to...
