Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
I am considering software that uses nRF52840, where one side will send advertisements and the other side will scan and obtain data from advertisements.
I am considering...
Hi,
I’m developing a BLE IoT product using the nRF52840 DK, where I need to send a payload of 60 bytes. In a previous response to one of my questions, I was advised to increase...
I have a requirement for PMIC which should include charging, sleep mode integration and should give simultaneously 2 outputs. One output should range from 3-5V the other one...
Hey
I have tried to enable and test coredump as shown in this example: https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-2-debugging/topic...
My production board doesn't support UART, but we have SEEGER JLINK using RTT to debug with. I'm using nRF5_SDK_17.0.2_d674dde\examples\dtm\direct_test_mode project.
If I...
Hello.
I am experimenting with the nRF52-DK board. The tool is segger studio on win x64. Bluetooth appears on the smartphone and disappears after a while. It is not connecting...
Hello,
On my custom board, I need to offload data from my NRF52840 chip via Bluetooth/BLE to my PC for processing. (Ideally using python to receive) Is this formally covered...
We're evaluating RSP with 1oT, and we managed to successfully swap the carrier using RSP with our nRF9160DK, running our standard application.
The nRF9161-DK, running the...
Hello,
i'm developing a custom board with nPM1300 + nrf5340. First things first, i purchased a nPM1300-EK to acquire the needed knowledge to make things working. Unfortunately...
Hi,
I have one nrf52840 board and one bosch BMA456 Shuttle board 3.0 flyer.
I am using zephyr-sdk-0.16.8.
zephyr build and flashing works fine, but when I use device...
Hello,
I am developing a solution based on nrf52-DK, using nRF52840. I have a .hex file produced by the R&D team So far I can flash successfully the board with :
drag...
Hi all,
Recently I am trying to start a secure MQTT connect between Rabbit MQ broker and nRF-9160 or nRF-9151.
nRF9160 is running Serial LTE Modem(SLM) application with...
I've been spending a long time trying to write a driver for the ILI9341 8080 8bit bus interface but all I can't seem to get the display to do anything at all. I'm just seeing...
