I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hi,
I can set up and run the GP timer on the nPM1300, but would like to know if the timer is running. At first glance it looks like TIMERSTATUS (ca, p113 of the PS) should...
Hi,
I an designing a module with either wifi connectivity or cellular network connectivity with host MCU. I am planning to evaluate nRF9160 for cellular network and nRF7002...
I am trying to use the Serial Modem Add-On (SM) application with the attached overlay-external-mcu.overlay. When DTR is asserted (active low), the modem stops responding to...
I would like to know the Host subsystem DN/QDID of nRF Connect SDK 3.2.0 for nRF52832. It is not described below. docs.nordicsemi.com/.../ble_qdid_qual_matrix.html
I am working with the nRF54L15 to create a driver for a peripheral which is controlled by two PWM signals.
My driver relies on the Zephyr PWM driver which goes back to your...
HI
How much current dose the individual GPIO pin source/sink for nRF5340 as in the datasheet V1.3 it is mentioned "Added guidance on maximum combined GPIO sink/source current...
Hello,
we want to setup an environment for automated testing of our bluetooth mesh system.
The test system should be able to provision and communicate over a device that...
Hi
If my calculations are correct the NORDIC whitepaper WP008 on PRINTED MONOPOLE ANTENNA for 2.45Ghz the quarter wave length antenna trace is not 92mm
For TOP layer PCB...
Hi,
I was trying to get the NFC Sample programs to work on the nRF52840 DK but the NFC tag is not being read by my phone. The program itself is running (confimed through...
I am working on a school project and need to set up SPI communication between a wiznet,W5500 and the nRF54L15DK. I can build and run my program but I am getting no responce...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hello,
With NCS v 3.2.1, I am working on a BLE application with nRF52840 dongle.
I was trying to add FOTA feature in my application by adding the following line to sysbuild...
I just ordered and opened up the nRF9160 dev kit from Digikey. I was going through the quick start and I named the device and when I went through the verification step, it...
Can you clarify, is it possible for the nPM2100 to set Vout < Vbat I.e. 1.8v out with 3v battery? The behaviour of the EV kit suggests not...
The datasheet isn't really...
