Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
I will calculate the capacitance of the external capacitors for the 32 MHz oscillator circuit, but the values of the Cpin for XC1 and XC2 are not specified in the the datasheet...
When I follow the use_gpio_pin_directly manual I get a compilation error:
```
/home/gal/dev/ism330bx_driver_contribution/zephyr/include/zephyr/devicetree.h:196:36: error...
Hello,
I'm tinkering (motion detection mostly) with a Thingy:91 unit (I don't have a DK board), and in general it works fine reporting sensory data to AWS IoT Core.
Last...
We’re developing a medical device under IEC 62304 and plan to use nRF Connect SDK. Does Nordic offer any documentation or process descriptions to support IEC 62304 compliance...
Dear Customer Support,
We are gathering the list of supported AT commands support for the nRF9151
Also experimenting available AT commands using the nRF9151DK
So far...
I’m trying to build and flash a BLE Mesh DFU application for the nRF5340 DK board, but it isn’t working. I selected the nrf5340dk_nrf5340_cpuapp build target only. Could you...
Hello,
I’m developing a composite USB device on nRF5340 (NCS v2.6.0) that exposes USB CDC + MIDI + Audio. When using the USB Audio interface, volume control works correctly...
I am trying to reset an nRF52840DK - it is visible within the nRF Connect SDK in Visual studio code but gives a timeout message:
[14:27:11] nrfutil-device reset --serial...
Hi everyone,
I’m currently working on a small, battery-powered tracking device based on the Nordic nRF9151 SiP . The goal is to create a compact and energy-efficient product...
I am unable to program the Thingy:91 using nRF Connect for Desktop → Cellular Monitor application , as described in the following link:
https://academy.nordicsemi.com/courses...
Hi,
what is the recommended way on the nRF91x1 to clear the Forbidden PLMN list?
Devices may get denied on networks repeatedly, filling up the FPLMN list. To ensure the...
Hi, we are still struggling with nrf9161 behavior and trying to mitigate data sending dropouts ( and ).
Here is one partial issue: we are currently using UDP and flushing...
using west update i just update the old version 3.0.2 to 3.1.1 and after take blinky code and build then i have got below error,also using the vs code i doenload the NCS v3...
Hello, While designing the hardware circuit for the CAAA WLCSP with internal LDO regulator setup on the nrf52810, I removed the 32.768kHz crystal oscillator and retained only...
I am currently developing my project using the nrf52832 and the nrf5SDK.
I utilized the peer_manager module, and in the application, when being connected as a peripheral...
