Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
Hi，
In Core Specification v5.4, there is support for Non-Connectable and Non-Scannable Extended Advertising (ADV_EXT_IND) without AUX packets. However, when using Nordic...
I am adding OTA support using mcuboot with mcumgr on a custom nrf54l15 board with the upgrade (mcuboot_secondary) partition on an external SPI nor flash (not QSPI). I am using...
Hi,
how to convert/format NCELL data to data that you can use to find the cell on a cellmapper.
This is a ncell result: %NCELLMEAS: 0, “06223A0C”, “20610”, “5334”,65535...
Hi,
I am currently working on making it possible to connect with different devices sequentially. It was told to me that it is possible to first scan all devices, and then...
hi support team,
may i ask do we have demo on how to test remote provision in ncs2.9.0?
i assume there are two possiblilities:
1.
For server, we need add below settings...
Hello,
We are using Raspberry Pi + NRF52840 as Borderrouter for Openthread using Radio Coprocessor design.
However we are facing stability issues on the RCP where it...
Hi,
Our project need 7 seperate PWM outputs, as the nRF52840 have 4 hardware pwm, I decide to use GPIOTE with PPI to create extra 3 pwm outputs to drive Red/Green/Blue...
Hello,I tryed to install the CMSIS Wirzard in SES on the video from https://www.youtube.com/watch?v=b0MxWaAjMco But it deosn't work. I don't know why. I did read the DevZone...
Hey,
I’m currently evaluating DECT NR+ using two nRF9151 DKs with the nRF Connect SDK v2.9.0.
According to the ETSI specification (ETSI TS 103 636-4 V2.1.1), the Physical...
While testing CoAP with NB-IoT I normally get PSM (sleep) delay = 20s before PSM mode is set (0.5mA with UART enabled), but after awhile PSM delay increases to ~4.5min (at...
Hi,
I recently added FOTA support on my project which runs on nRF5340 + nRF7002. I am currently working on a devboard, nRF7002DK.
Previously, I was running the project...
Since I need zephyr version 4.0 or newer, I tried updating my project to the nRF Connect SDK v3.0.0 as well as the toolchain. I know that they are not fully released yet....
Hello,
Currently the nrf-connect extension offers board targets under build configuration. These are categorized as "Nordic SoC", "Custom boards", "All". As I have understood...
After updating to 3.0rc2 from 2.9.1 Mesh example fail to build. Crypto related issues.
yml modules -
- name : nrf remote : ncs repo-path : sdk-nrf revision : 52921acad685bb3815af94d9a3a4a11ad209fcd0...
