Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I am trying to communicate with my IOT using wired uart serial port. I am using 840(MCU) (with softdevice #113).
code:
My Issue: Each time I am trying to run it while...
Hi,
I am trying to reduce the consumption of my Thingy91 device in idle mode. I am working with NCSv1.3 and the example asset_tracker. I am currently registering 0.60mA...
In our NRF9160 application, we do not have a UART available and have to implement other means of logging crashes.
We have written our own k_sys_fatal_error_handler but it...
I am using a generic nRF52 dev board with the Arduino nRF52 core . I am trying to get a sample BLE service to display, but it cannot find it on my BLE scanner. After I couldn...
Hi,
I am trying to read read all nearby base stations' Cell ID, TAC, MNC, MCC.
Is this even possible to do with this DK?
At this point I have found these commands...
Hello,
I am trying the UDP sample for the nRF9160 DK board, using the iBasis SIM card that came with the kit.
The problem is that it does not register onto the network...
Hello,
I’m trying to interface the MAX32664GWEB+T sensor hub with the NRF52 by using I2C, I’m wondering if you could provide me any recommendation, libraries or codes for...
What I want to do is do UART communication (UART_1) between nRF52840 and nRF9160.
From the nRF52840 side, uart_poll_out is OK, From the nRF9160 side, uart_poll_out examined...
Hi Nordic team,
We have planned to use nRF5340 based BLE mesh device which is interface with sensor
We would like to transfer customized user data from one node to another...
I tried different nrfconnect examples and noticed that: C:/Nordic/v1.4.1/zephyr/samples/basic/blinky/build_nrf9160dk_nrf9160 blinky: rebuild solution + flash: OK also hello_world...
HI,
I am working NRF52810 with SDK 17.
I am able to pair my nordic device to mobile. but after pairing I want to send some data/receive some data.
how can I achieve...
In SDK 17.0.2, most places it looks like BLE_GAP_ROLE_CENTRAL is allowed to be undefined, except in nrf_ble_gatt.c line 142. Was there supposed to be "#ifdef BLE_GAP_ROLE_CENTRAL...
Hi Team, I am prototyping a product that includes DFU OTA using nRF52832. To get familiar with the topic, I am experimenting with the buttonless DFU example.
It is working...
Hi Nordic!
I am completely new to the Nordic MCU. Please, where can I find all the information (technical datasheet) about the NRF52840? What peripherals can I connect on...
Hello,
I want to use radio to send and receive data periodly. So I refer TimeSlot API in ' devzone.nordicsemi.com/.../setting-up-the-timeslot-api',and also refer the radio...
