Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello,
I had purchased 6 nRF52840 Preview Development Kit boards in 2017 for study and development.
This year, I want to re-use the PDKs for a new BLE-THREAD related PoC...
Hi, i'm trying to load the aws_iot sample and I'm running into mqtt_connect, error: -95. Based on other posts, it seems my certificates might not be properly loaded. As far...
I am building on a BLE DFU project which already has a NRF_FSTORAGE_DEF for allocation of non-volatile data used by DFU. I want to add another instance of NRF_FSTORAGE_DEF...
Hello,
I am using the modem callback:
To check if the modem is connected using the following code:
However, as far as I understood this only indicates that the modem...
Respected Sir, Mam
I am Noel Joe Riju Antony a student of Amity University, Noida, India pursuing a B.Tech in Aerospace engineering. I am currently working on a CW radar...
Hi,
I've got a Thingy:91, which I've spent a lot of hours in understanding the different samples. I want to be able to send GPS information to my Azure IoT hub device...
Utilizing SDK 15.2 and Softdevice S132, when debugging with Segger Ozone and starting from main or after triggering a reset to restart at main an ERROR 8 [NRF_ERROR_INVALID_STATE...
Tried running android app in debug mode, but I could not see any data on the crash.
tried resetting the board a few time and re commissioning.
followed the guide to set...
I found a lot of posts with this warning/error, but I could not find a fitting solution among them.
in my case, I copied the `peripheral_lbs` project to another folder,...
Hello
I have a few questions regarding the "ble_thread_dyn_mtd_coap_cli" example:
In the "main.c" file, I notice that you have created timers to call "sd_ble_gap_conn_param_update...
Hello.
I have a custom board with a uBlox BMD300 on it. The BMD300 is based on the nRF52382. The BMD300 had a pre package firmware in it that acted as a BLE UART bridge...
Hi all,
I am using the python bindings in recent weeks to development a BLE scanning device and have found the python bindings very useful for getting the kit up and running...
On MacOS Big Sur (11.2), trying to get started with nRF5340 samples, but getting create_nordic_project.py failed (1) errors.
I installed manually using the nRF Connect v3...
We are in the evaluation phase of a technology that is planning to use sound to transmit data between phones and devices.
We are currently using Quiet open source library...
