Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hello,
We are at initial stage of design proposal.
Could you please provide the clarification on following points?
1. nRF9160 SoC is interface with BLE chip nRF52480...
Hi everyone,
sadly one of my nRF51-DK boards seems to be terribly bricked.
During firmware update nRFgo Studio (on Windows) stopped responding. After a (long) while I...
I could successfully installed development environment.
Could import Blinky application and could successfully build.
But couldn't import asset tracking application...
I have an product that has no IO capabilities but requires MITM protection, authenticated pairing and an encrypted link. My understanding is the security defined in the Bluetooth...
After I select Yes to All, or No to All, it tells me to get I license, which I just click continue, and then after that everything works fine.
The install is kusher according...
If i want to provision a device by mobile app over GATT, will this device support proxy feature to provision directly or provision undirectly over one proxy node
Hi. I am implementing a low power operation in my firmware, but the UART de-initialization is causing me odd issues. In order to intialize, I call the function UART_Initialize...
Hi, I am currently working on " asset_tracke r" application. Actually, I need RSSI values to be captured in "asset_tracker", application. So I am trying to migrate "lte_ble_gateway...
Hi,
Mesh SDK 4.2.0.
In light_ctl_setup_server.c,
This subscription list sharing doesn't share it with Generic Power OnOff Setup server but only does it with Generic...
Hello,
i'm working on a NRF52810 on which i have ported FreeRTOS because i'm sharing library with another NRF52832 that embeds FreeRTOS too.
I'm issueing an overconsomption...
Hello,
1) I updated the modem software with connect programmer trhu a USB connection on the Thingy:91
2) I updated al the HEX files in the "thingy91_fw_2020-04-29_bc7ade8b...
Hello, I'm a newbie who just started nordic. Please excuse me because I don't know many things.
I use nrf52DK board and SDK V17 and I am developing it using various ble_SDK...
Hi everyone,
I have developed a Zigbee application for the nRF52840 board and now I need to migrate to the nRF52833 board.
Are there any indications on how to proceed...
hi everyone, I am having a problem making the door sensor. I want to optimize the power of the sensor so after acting I will put the sensor in system_off mode. I have the...
Hi,
We were trying to flash the nrf modem firmware using the 'pynrfjprog'.
When only one nrf9160dk is connected , the flashing is success and no error.
But when multiple...
