Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi all,
Does anybody know how to use NRF_LOG in Mesh SDK, because I need to print float numbers. I know that I need to use NRF_LOG_FLOAT_MARKER because I was using it inside...
Using NCS V1.4 for Mesh on a nRF52840, My customer wants to send higher rate sensor data via mesh. It seems the fastest continuous rate they can obtain is about 1Hz. When...
Hi,
How is the Inter processor communication handled between NRF52840 and NRF9160 in Thingy91 ? It was not very clear from the schematics for me
Can you tell me which...
hello Nordic
recently i encounter a claim that nordic to nordic BLE is faster, or capable of transferring more bits of data per second, then a nordic communicating with...
Hi,
I Have been trying to understand how to flash the nrf9160 IC using SWD and segger. Completed up to the build and run.
Need to know If I make some changes in code...
I am on SDK15.3, NRF52840, armgcc, makefile, console
I need to print a double float number in format of "x.xxxxE-xx". I already know that NRF_LOG can only print float with...
I am using sdk17. I'm implementing central, and I'm using app_ble_out_c to implement it. But there's a problem. This example matches only the specified nus uuid with the service...
Hi, I want to send Door Lock Event Notification commands.
so I modified ZB_ZCL_DOOR_LOCK_SEND_LOCK_DOOR_RES macro in zb_zcl_door_lock.h file.
The result...
hello,
i added scan_rsp_data to add a name on my beacon, but now i cant see manufacturer data on the ble_gap_evt_adv_report_t structure but i can see that perfectly on my...
I'm seeing the modulated output of %XRFTEST offset by approx. 1.675 MHz from the set frequency. Modem version is v1.2.2
Here's my command:
AT%XRFTEST=1,1,1,19500,23...
Hi!
Looking at the schematics for the nRF52833 reference circuitry I see that when USB is used, the VBUS is connected to the C18 capacitor, then GND, and if USB isn't...
I have programmed my device with ble_app_rscs available on nRF5_SDK_15.3.0_59ac345. I was expecting it the main loop
the device will only consume 2 uA however it is consuming...
After a few configuration issues we have finally got a connection with the asset tracker application. However we are not getting far enough to send data.
The log shows a...
Hello,
i am trying the nrfsniffer 3.0, but all the packets seems to being dropped.
I am using:
* BLE400 with nrf51822 module (firmware flashed with stlink )
* Linux...
