here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
I am working on nrf52832 and SDK V15_3 and Softdevice S132 . I want to enable 2MBPS mode to achieve maximum throughput. I have checked different links in nordic devzone but...
Hi , I succeed to flash the firmware to Thingy52
you can see the attached 2 pictures one is for the nRF Mesh app and the second is the Thingy 52 (Four units) which are ...
Hello,
I am using nRF52840 DevKit, SDK 16.0.0 and SoftDevice 113 v701
I am looking at nrf_bootloader example and want to configure a watchdog that keeps running even...
Hi,
I'm wondering what is a good way of keeping track of when the device is inside the active time window so that the data is being sent at the correct time.
Here is my...
Hi,
I'm working on two projects, in the first one, nRF52832 (softdevice S132 V6.1.0) is used as a slave component communicated with STM32L4+ over UART and the second one...
Hello,
I have been using nRF52840-DK and also nRF52840 Dongle for testing and I found an interesting behaviour when I established my test setup. The RF module acts as an...
Hi All,
We have a product based on nrf52832 that has a custom ble service with 2 custom characteristics.The first one is to send data to the nrf device and the second one...
Hi
I opened the Watchdog in the user application,and do nothing in the bootloader.Then when I use DFU,the CPU reset appears.How can I to deal with it?
And when I upgrade...
Hi
I am looking for some specific contract developer help to build and Android app to update Firmware in devices using DFU and the buttonless service. Obviously there are...
HI,
We are evaluation the nRF9160 in the devkit and we are trying to obtain the values specified in the nRF9160 Product Specefication v 1.1. After following the different...
Hello,
There are many questions out there on correctly determining the SAADC pin input voltage limits. The equations given in the product spec is very straight forward:...
We are creating and application that will use the Serial port to communicate to a host using an RS485 protocol. We have it working in SDK 15, but we are now trying to build...
Hello All, I want to generate Bi-Phasic two PWMs with 180 degree interphase delay and variable Duty Cycle with variable frequency upto 250 Hz in nRF52810 SoC. Can you please...
Hello, how can I use the functions in nrfx_twim.c
Using SES and the CMSIS config wizard, I have picked:
NRFX_TWIM_ENABLED 1
NRFX_TWIM0_ENABLED 1
NRFX_TWIS_ENABLED...