Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
Hi everyone,
I am new to segger embedded studio. I want ibeacon firmware sample code to advertise uuid, major, minor, tx power, advertisement interval. I want to change...
We're developing a product where a single NRF52840 board - lets call it the central- serves as the focal point for multiple NRF52840 boards spread out across an area - lets...
I am not able understand the difference between APPROTECT and BPROT . Can you please clarify ? and if we enable the protection then how to disable it again whenever we want...
I've seen many posts about LL_LENGTH_REQ causing disconnection on certain Android phones and the solution from Nordic is to add a 100ms delay. Can someone from Nordic definitively...
Hi community,
in our setup we use the LSM6DSL IMU using TWI. First we initialize the TWI peripheral, then we configure the IMU. After that we initialize PPI to automatically...
I am trying to build the project "thingysdkv210" which is downloaded from https://www.nordicsemi.com/Software-and-tools/Prototyping-platforms/Nordic-Thingy-52/Download#infotabs...
nRF52 DK
HTS example
I added app_timer_stop_all() in the ble_evt_handler() of main.c, under the case of BLE_GAP_EVT_DISCONNECTED, but the battery service timer still...
need help on multiple things
All work is on the DK 840 board using sdk15.3
Started with this link
https://rigado.zendesk.com/hc/en-us/articles/360025376053-Add-Nordic...
Is it possible to run the Zigbee Light Switch example with the internal RC.?
On the sdk_config.h I have changed the following:
#define NRFX_CLOCK_CONFIG_LF_SRC 0
But...
In the only example in SDK16.0.0 with soft_device and Free RTOS, configMAX_PRIORITIES is set to 3, which means available priorities 0,1 and 2.
Is it possible to change configMAX_PRIORITIES...
Hi i'm very new in using Nordic nRF52840. Got 2 questions:
1.Why does each example project contain blank/mbr/slxxx folders? in these folders they all have a copy of the...
Hi,
we've been experiencing some strange issues with the OTA DFU on nRF Connect for Androind in the past two days.
We've been using such function on a regular basis with...
I am trying to transition my Nordic SDK v12 project from Keil to Segger Embedded studio. I followed the tutorial steps such as placing ses_nrf_51_startup.s file in Internal...
Can I use an external edge-triggered (negative edge) interrupt (on a GPIO pin) to trigger an I2C write via PPI? If so, do the I2C registers need to be reloaded each time?...
