here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
I have an application that uses many TWI buses, on many pins of the nRF51. I handle this by initializing/uninitializing a single TWI bus for different transactions. I ran...
in S130 v2.0.0, what is address of central?
i'm using ble central tutorial successfully compiled.
in case of ble peripheral, i can set address whenever running.
so ble...
Dear Nordic Team,
Thanks for supporting.
How to add custom characteristics in standard service ?. I am using Health Thermometer service (HTS). I want to add two custom...
I mounted the chip onto my own PCB, I am not using a devkit, My board is "Wireless-Tag WT51822-S2", it is a module that uses nRF51822-QFAA as (SoC)
I am the ble_app_uart...
With the release of SDK 12.1 the Serialization of S130 is now deprecated.
Within SDK 12.0 the Serialization was supported NOT at all.
When this is true, I have to stay...
I'm trying to stream data in real time from 4 different sensor units to my computer. Each of these sensor units has an NRF52 module that sends data at 50 packets per second...
Hello, I'm south korea student in dongguk univ.
and i want to know how can i send the message on my board(not use the terminal ).
I use the keil uvision4.0, nrf51822...
Hi,
I want to change eddystone_url_data parameter in experimental_ble_app_eddystone (C:\Keil_v5\ARM\PACK\NordicSemiconductor\nRF_Examples\10.0.0\ble_peripheral\experimental_ble_app_eddystone...
Hello, i study the cryption.
First, I'm not good at english...
I use keil uvision4, nrf51822, s110 softdevice
I need check the run-time.
how can i check the runtime...
Hi,
We created a custom board, with the nRF52 and the 32 MHz crystal oscillator according to the reference circuitry.
We use ESB to communicate on RF, and it needs the...
I am new to NRF52832. I want to monitor continuously PIN 3 where I have connected USB to check whether my USB is connected or not. How can I do that. Please reply ASAP.
Hello,
I made an application inspired from the ble_uart example project.
I encounter now a problem that I don't have with the ble_uart example.
I found that after...
Hello,
I have problems connecting a nrf52 with a TI cc2650. The cc2650 is the peripheral and I can connect to the device from my PC and from some other devices. But when...
