Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi
I would like to use the arm based energy micro MCU to update 51422 via UART
I've understood how the firmware update example with hci, but I need a set of hci api to...
Hello,
I in the nRF8002 data sheet it mentions a Programming tool for the nRF8002. Can you please send me the partnumber of this tool? Also, if a programming house wishes...
"Install the Master Control Panel and the nRF51822 Development Dongle (PCA10000)
Download and install the Master Control Panel from our website. Make sure to select...
Hi,
Been using nRF51822 before but on this new design I have an external MCU running the main duties.
I've been reading up a bit on both but would like to get some thoughts...
Hi nordic engineer:
I want to know the right process to delete the bonds when the device connected.
There is a button used for bonding. When it pressing by more than...
That means, that the nRF51822 is always allowed to send, but on it's receiving side, he could slow down the opponent side by using it's Rts line?
I now, I could archive that...
Hi,
I made simple command shell via UART. It works fine when I type commands in terminal by hand. But I run into troubles when BLE chip is fed from MCU that send characters...
When I connect my ble mouse to the PC win8.1 , media button works normal.
When I power off and power on my mouse, it reconnected to win8.1 PC quickly, sensor ,left button...
I'm using the nRFgo motherboard (nRF6310 together with the PCA10004 Cpu board. I'd configured the nRF51822's Uart to 1 MBaud).
Is the RS232 level shifter (which is part of...
It's this will be work?
// Initialize the Bond Manager.
bond_init_data.flash_page_num_bond = FLASH_PAGE_BOND;
bond_init_data.flash_page_num_sys_attr = FLASH_PAGE_SYS_ATTR;...
Hello：
I need to ask you after the next programmed into how this routine testing 。（nrf51_sdk_v4_4_2_3355\nrf51822\Board\nrf6310\ble\ble_app_alert_notification ） The iphone...
Dear Developer Zone,
I am working with nRF51822 and IOS.
My device can only be connected to one central, so to one iPhone. To refuse connection from others centrals...
Hi all,
I've got some questions about the DFU OTA Nordic example (nRFToolbox):
What is available full stack update or profile update?
Firmware flow, does it need to...
Hi Folks,
I'm running into a problem with the pipes on my nRF8001. After I issue a Connect (0x0F) command, I receive:
CommandResponseEvent (0x84)
ConnectedEvent...
We have setup the RX and TX modes for ANT+ in Advanced Burst mode.
The setter function works (can confirm that by using sd_ant_adv_burst_config_set());
However when...
