Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
I want to create a 1MHz timer using TIMER2.
I try to start the timer with the following settings, but the device probably hangs.
I also use app_timer, is it a problem...
Hello, Not so long ago I asked this question and the solution I was given is still working for the devices I was using. Now I've received a new version of the device in which...
Hello,
I am using nRF52832 DK module(for master), and breakout board(for slaves, 4-slaves).
I have some problem while BLE communication.
First, I am wondering if I can...
Hi,
I'm getting error on connect to cloud server (socket.nouslogic.com:443) with error code is 45 ( EOPNOTSUPP).
Here are detail:
1. Using https_client example on nRF...
Hi,
I am going to use a timer in my code which includes ble_app_uart (using app_timer) and saadc examples. I need this timer to read time during the program.
I know...
what I use project is "ble_thread_dyn_template" , Is there any way to replace the app's UART console with 'BLE' - i.e. instead of receiving 'ot' commands from UART console...
I need to read (and clear) the general purpose retention register. I cant start the Soft Device just yet, so cant use the sd_power_gpregret_get and sd_power_gpregret_clr functions...
Hi there!
I'm back again, with another possibly stupid mistake. I'm using ARMGCC in combination with Make, nRF5 SDK, nRF SDK for Mesh, FreeRTOS and C++. I wrote my own mesh...
Hi Dev team,
I am currently using the NCS v1.5.0 and have a Thingy91 v1.4.0 with me. I want to test the FOTA v2 update from the nRF Cloud to the Thingy91.
I tried using...
I am trying to tune my NFC antenna . The antenna is printed on the pcb. The same Laird antenna is used in my pcb. Based on the antenna tuning white paper I am trying to tune...
When I connect my Thingy 91 to my usb port open up nrf Connect and push Sw3 and turn on the board power I do not get any devices to show up under device selection in rf connect...
In our application the prospective Nordic NRF5340 MCU is to communicate with another MCU at the maximum 3Mbps.
Can this speed ( 3Mbps) be achieved on NRF5340?
As mentioned...
Hello, I'm hoping that I missed something in the code and not something that might be inherent with nus and fds. Combining SDK 15.3 template, uart and fds examples, with some...
Hi,
We have a working solution on the SDK15.0.0 with a custom board based on nrf52832 s132. I'm using the nrf52dk PCA10040 to program my boards. For this board we use...
