Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
Hi.
I am using the nRF52810 for Bluetooth SIG certification.
S112 6.0.0
SDK 15.0.0
I am testing using ICS of QDID 102861 and 49943, but a failure occurred in the GLS...
We are upgrading our product from SDK15 to SDK16 using DFU over USB. When we perform a DFU update (BL, SD, and App) form SDK15 to SDK16, it works fine. Then if we perform...
Hi! I'm studying the basic codes of the BLE Blinky Application for peripheral! ( https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v15.0.0%2Fble_sdk_app_blinky...
Hi,
I'm making a custom board with NRF52840 and would like to confirm some schematic/layout considerations for things I couldn't quite find in other posts. I apologize if...
Hi Nordic Team,
I am using SDK 16.0.0 with Softdevice S132 version 7.0.1 on the NRF52832 and using SES v4.52c on Linux. I have managed to run and sucessfully execute the...
I use the following code to enable a timer that clears itself to loop continuously via the compare0-clear shortcut. (I then use other compares, PPI, and GPIOTE to output pulses...
Hi Nordic guys,
We just integrated the AGPS function using SUPL library with the GPS driver to accelerate the GPS fix time.
We tested our code with near windows environment...
Hi,
I managed to download the latest firmware on my thingy91 and it looks working properly on the LinkMonitor. Anyway, it stays always in searching LTE and never goes to...
hello everyone. We found a problem. when nrf52832 is working, after the core power supply is sudden short and release, the power supply mode is LDO and the current is about...
I have a device that has multiple NRF52832 modules
Is there any issues with setting the mac address of each of the modules to the same thing...
e.g. would there be any...
Working with SDK v16 (S140 v7.0.1) I get error code 0x10 (NRF_ERROR_INVALID_ADDR) when calling nrf_sdh_enable_request(). Setting into that function I see that the error code...
My application uses the nrf9160 in eDRX mode. I regularly have the problem, that when switching the modem to OFFLINE mode (same for POWER-OFF mode), the modem is not responding...
Dear all, I have a plan to use NUS service alongside with proxy Mesh. I tried to find documents about mesh performance with Nus service? Could you please give me more information...
I wrote two applications, and both will never know what application starts first. So I design a handshake that works something like this.
receiver
Set to receiver, look...
